| [ Total Views: 534 | Total Replies: 6 | Thread Id: 94967 ] |
|
|
 Mattriots
Seriously Crusin Dubber
Posts: 131
Threads: 26
Registered: September 6th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 23rd, 2012 at 10:32 PM |
|
|
How to install a new hood release cable
Just pulled out the old hood release cable from my 65 beetle cos the knob was all cracked. But now I can't install the new one, the cable is getting
caught up in the tight bends in the tube down near the latch mechanism.
Are there any tricks on how to feed the cable all the way through the tube?????
Such a simple task, it's so frustrating I can't get it!!!!
Thanks for any help
Matthew
|
|
|
annosL
Officially Full-On Dubber
Posts: 378
Threads: 43
Registered: December 28th, 2008
Member Is Offline
Location: albany
Theme: UltimaBB Pro Blue ( Default )
Mood: need to win lotto
|
| posted on January 24th, 2012 at 12:04 AM |
|
|
Maybe some silicon spray may help?
|
|
|
Mattriots
Seriously Crusin Dubber
Posts: 131
Threads: 26
Registered: September 6th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 24th, 2012 at 07:57 AM |
|
|
I tried wd40, but no luck
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on January 24th, 2012 at 08:16 AM |
|
|
I've always had a win just by turning/twisting the cable at the difficult turns.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on January 24th, 2012 at 11:29 AM |
|
|
| Quote: | Originally
posted by Mattriots
Just pulled out the old hood release cable from my 65 beetle cos the knob was all cracked. But now I can't install the new one, the cable is getting
caught up in the tight bends in the tube down near the latch mechanism.
Are there any tricks on how to feed the cable all the way through the tube?????
Such a simple task, it's so frustrating I can't get it!!!!
Thanks for any help
Matthew
|
Hi Mathew
trick is... stick some grease or vaseline onto the end of the cable before you stick it in and a bit of oil into the tube [if you can] or wd40
spray...
as You push the cable in twist it round and round as you go
so when it its the tight spots it should slip over them..
cheers
Lee
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
Mattriots
Seriously Crusin Dubber
Posts: 131
Threads: 26
Registered: September 6th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 24th, 2012 at 12:16 PM |
|
|
Thanks, I'll give it a try tonight and let you know how I go
Fingers crossed!!
|
|
|
Mattriots
Seriously Crusin Dubber
Posts: 131
Threads: 26
Registered: September 6th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 24th, 2012 at 05:58 PM |
|
|
Ok, so I used heaps of wd40 down the tube, and the tip of the cable(wire) I bent back on itself and crimped it down hard with some pliers so it was a
nice rounded end. And with a little jiggling it finally went through!!
Thanks for your help lads
|
|
|
