| [ Total Views: 1555 | Total Replies: 4 | Thread Id: 95698 ] |
|
|
 countrypiper
Learner Dubber
Posts: 4
Threads: 2
Registered: June 11th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 6th, 2012 at 11:48 AM |
|
|
will 1300cc single port heads fit onto 1200cc cylinders
Hi,
I've got a really good 1200cc engine, and I want to improve the breathability of it. I've already sorted out the exhaust with a tuned 4 into one
system, and now it's time to look at the intake system. I have an old 1300cc engine that I'm stripping and rebuilding as a 1600, and before I take
the heads off the 1200 and replace them with 1300cc heads, I thought I'd ask to see if anyone had done this before, and whether it gave the old 1200
any more power. I know I'll have to cut the 1300 manifold to reduce it's width, but I'm willing to do this if it gives more life to the 1200 (which
revs to 6000 rpm ). If anyone has done this, I'd be happy to hear from you. Thanks. |
|
|
whatnow
A.k.a.: Henry
Custom Title Time!
Posts: 1000
Threads: 54
Registered: January 11th, 2003
Member Is Offline
Location: armidale, northern tablelands NSW
Theme: UltimaBB Streamlined2
Mood: 14's are the new earlies.
|
| posted on March 7th, 2012 at 01:28 PM |
|
|
it can be done, see the vintage speed forum at http://www.thesamba.com as this is
covered there in detail.
if your 1200 heads have been modded flow enough to rev to 6000 i doubt that 1300sp heads will flow any better.
|
|
|
coletrickle
Wolfsburg Wizard
Posts: 661
Threads: 34
Registered: April 22nd, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 7th, 2012 at 03:09 PM |
|
|
I'd be leaving the long motor alone,and looking at a larger manifold t section(1600sptp with modded ends)and a stromberg off a HQ racer 1.1 exhaust
rockers ratio intake rockers.and if you could pick up a slip in big bore kit that would be a ripper little engine.I had a 1370?40 horse with illegal
vee heads pict 30 scat econno exhaust and it made 48 hp @ wheels.1200s are heap of fun.Keep us posted
|
|
|
chequer57
Seriously Crusin Dubber
Posts: 125
Threads: 15
Registered: February 12th, 2006
Member Is Offline
Location: Sydney - Sunnly Land of Oz
Theme: UltimaBB Psyche Red
Mood: Moody
|
| posted on March 7th, 2012 at 11:38 PM |
|
|
The Vee guys used 113 101 373 or 113 101 371D 1200cc heads.
Other trick other than careful porting is the partial installation of the inlet valve guides.
Formula Vee engines make all their power out of carefully optimising the inlet track and having the in the bottom end balanced.
The Formula Vee rules are so restrictive most decent bolt on bits would make an engine more powerful than leaving it in fvee trim.
Formula Vee, preserving engineering museum pieces in Australia since 1964
|
|
|
countrypiper
Learner Dubber
Posts: 4
Threads: 2
Registered: June 11th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 12th, 2012 at 05:03 PM |
|
|
Thanks for all your advice. I've decided that swept volume is king where power is concerned, and I'm going to convert my 1300 second hand engine
into a 1600 and replace the 1200, without mucking around with the heads on the 1200. There seems to be a pretty well priced kit on Classic VW site
that should fit my 1300 well enough - or so I've read ( https://www.classicveedub.com.au/cvd_new/part_detail.aspx?parts_id=15189 ). I now need to organise the 1300 case to be
bored and the deck height done - then its on with a rebuild (and a few modifications, like an external oil filter!). |
|
|
