| [ Total Views: 20416 | Total Replies: 169 | Thread Id: 96078 ] |
| Pages: 1 2 3 .. 6 |
|
|
 D-train
Seriously Crusin Dubber
Posts: 180
Threads: 40
Registered: October 2nd, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 28th, 2012 at 07:21 AM |
|
|
57 junkyard dog oval
as found, took a couple of years to get it tho.
beautiful dash
found rear guards for it, kind of matches.
pans rooted, so off with its head
new sides goin to go in, thanks to Al an Steve at Das Resto Parts for stocking the bits i needed.
some accessories goin on it.
from a wrecked 56 bug, need new rivets for it, an yes i will drill the original rings.
flying bonnet emblem, cast from an og one, (thanks Bob) i made a few of those.
bonnet straps
3 spoke
ratty mangels, but thinkin ill run stockers. still undecided.
with rusty flying swastika logo hubcaps
57 36er with the judson, some NOS bits goin on this thing as well.
theres another build thread about this engine only a couple of weeks build difference btween the car an engine.
started chassis
trial fit the wolfsburg west halves, thick metal an good fit
drilled holes all way round.
then welded the shit out of it
needed a little tweaking after initial welding for the rear half, but overall a good fit an impressed with the quality. grind back the tops an get it
ready for por15 all over it.
cleaned out all the cable tubes except for the choke, so off to find some tube and install it instead. bit of work involved but worth it in the end
both sides now welded in.
cuttin tunnel to fix cable tube
reattached rear plate thingy
rubber mat buttons
both sides done finally
put on the pedal cluster to weld in the bottom lockin plate
trialed the rubber mats to make sure i got the buttons in the right spot
loaded up for sandblasting
chassis is 100mm too long to fit in the tray. oh well
beer an tools for headlights
early bosch glass in early bosch frames, had to drill holes for the hinges, prob should of saved the frames, but if i put them in the cupboard for a
rainy day they will never be used.. purists will hate me now
finally got out to stans an had a chat about the 36er, i already knew it had been rebuilt, but he was quite impressed with it an how good of condition
it was in, even said the bearings will be fine to run, but if ive gone this far, might as well change them all out.
used his gear puller to pull off cam/dizzy gear.
new bearing on
heat up gears to slip back on
all done, crank is good to go back in now..
was goin to do the rod bearings as well, but chose against it as they are still really good as well..
hot washed the case an heads now to clean them up a bit before reassembly.
back from blasters
por 15
engine work.
got a high flow oil pump goin on it, so had to change the studs on the case.. u can see the difference.
good to go higher flow pump now!!
checked the cam in the case, it wasnt ovalled an sloppy so good to go again..
will turn straight..
nos pushrods, checked the clearance in the case an adjusted tabs as required..
dropped in the dowel pins for the bearings
lined up bearings with pins an dropped crank in
got cam right
an presto!!
high flow pump bolted in
new rear main seal, shims an gasket installed
polished flywheel for a good fit
all on an checked the end play, good clearance an crank/cam turn like factory
dizzy drive gear.
accidentally dropped the spacer shim in the case, nothin a good magnet an patience wouldnt get... wont do that again tho..
waitin on pushrod tubes to turn up then the heads/barrels will be on... wont be long at all!!!
cleaned up the heads, pretty good nick too.
rebuild a fuel pump with bigger spring for judson.
used wolfsburg west rebuild kit for internals..
nos base for pump
inserted return line screw for fram system an bolted up distributor
crank pulley an tinware, enough room for the bigger oil pump as well which was a concern i had.
and judson bottom pulley on as well..
tried to take out the studs for exhaust from the heads but kept snapping them, so off to machine shop to get them out, i hate gettin other people to
do work for me...
Back from work 2day, so will get into it again this week
|
|
|
Turbo54
Veteran Volks Folk
Posts: 2220
Threads: 268
Registered: July 13th, 2004
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
Mood: Boost'n
|
| posted on March 28th, 2012 at 07:36 AM |
|
|
Great work Dion, keep it going. I have the same headlights and bonnet straps for mine.
T54.
C'mon kids gather round,
there's a new sensation hitting town,
It's moving straight, low to the ground,
it'll pick you up when your feeling down.
|
|
|
5lam
A.k.a.: Dave
Wolfsburg Wizard
AKA: BlackBug
Posts: 520
Threads: 38
Registered: March 19th, 2006
Member Is Offline
Location: Gold Coast, QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: Slammed
|
| posted on March 28th, 2012 at 08:31 AM |
|
|
Sooo jealous right now!!
[size=5]Custom doesn't come in a Box[/size] |
|
|
annosL
Officially Full-On Dubber
Posts: 378
Threads: 43
Registered: December 28th, 2008
Member Is Offline
Location: albany
Theme: UltimaBB Pro Blue ( Default )
Mood: need to win lotto
|
| posted on March 28th, 2012 at 12:04 PM |
|
|
Great build! thanks for sharing
|
|
|
D-train
Seriously Crusin Dubber
Posts: 180
Threads: 40
Registered: October 2nd, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 28th, 2012 at 04:46 PM |
|
|
back from work an did 5mins of work 2day before the call of the ocean got to me again...
i should have it in my engine stand, but im in the process of dismantling another one as well, oh well...
new barrels an pistons with new rings in them ready to rock
drivers side
passenger side
head on with crush washers an paper gaskets
other side done, head to head now finished, have to find my feeler gauges an do the clearances...
more tomorrow...
|
|
|
tar76
Custom Title Time!
Posts: 1622
Threads: 95
Registered: December 18th, 2009
Member Is Offline
Location: Ningi Qld
Theme: UltimaBB Pro Blue
Mood: Rollin with The Dub Collective
|
| posted on March 28th, 2012 at 04:51 PM |
|
|
Nice work man
"Obey your Dreams"!
62 Std beetle.
65 11 wnd Split "The Cross".
6? coming very soon!!!!
|
|
|
LUFTMEISTER
Veteran Volks Folk
Posts: 2041
Threads: 119
Registered: July 13th, 2005
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
Mood: BRISVEGAS in a state of flux
|
| posted on March 28th, 2012 at 05:18 PM |
|
|
I'm not seeing much engine assembly lube???
Customer service is not dead in Australia.
Always after HAZET & MATRA & VW factory tools
|
|
|
D-train
Seriously Crusin Dubber
Posts: 180
Threads: 40
Registered: October 2nd, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 28th, 2012 at 06:38 PM |
|
|
Luftmeister, Everything is been lubed, look behind the barrel on the right, there is a oil can that is one of my fav things I have..
Not goin to fuck it b4 I run it..
|
|
|
LUFTMEISTER
Veteran Volks Folk
Posts: 2041
Threads: 119
Registered: July 13th, 2005
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
Mood: BRISVEGAS in a state of flux
|
| posted on March 28th, 2012 at 06:53 PM |
|
|
Hey just checking. Normally there is lube everywhere on
gears and rods and cam. Looks good. Where did you get the pans from? Sick of brazilian rubbish.
Customer service is not dead in Australia.
Always after HAZET & MATRA & VW factory tools
|
|
|
D-train
Seriously Crusin Dubber
Posts: 180
Threads: 40
Registered: October 2nd, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 29th, 2012 at 05:04 AM |
|
|
| Quote: | Originally
posted by LUFTMEISTER
Hey just checking. Normally there is lube everywhere on
gears and rods and cam. Looks good. Where did you get the pans from? Sick of brazilian rubbish.
|
Got them from das resto parts, they are the Wolfsburg west ones, good thickness on them as well, I've had brazillian ones b4 as well an these are far
superior to them.
|
|
|
D-train
Seriously Crusin Dubber
Posts: 180
Threads: 40
Registered: October 2nd, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 29th, 2012 at 07:10 PM |
|
|
some more on the engine. ill get onto the body soon...
finally found where i put the oil cooler, so on it went.
head tinware, heater boxes on
mmmm, arbarth
j pipes were fucked so new ones on ww ones.
lined them up an tacked them
ready for welding
welded up an installed back on engine.
heater boxes cleaned an installed in workin condition again
more tinware installed
carb manifold an leads installed
generator and fan housing installed.
compressor put on the manifold, carby just sitting there, still some work to do to it. Magneto connected, belts, just starting the fram set up....
installed lines
goin to make a bracket mount for this and the mystery oiler
shouldnt be long till i can start the old girl for the 1st time in who knows how long...
|
|
|
empi
A.k.a.: Empstar
Compulsive Aussie Vee Dubber
Posts: 4131
Threads: 178
Registered: August 27th, 2002
Member Is Offline
Location: melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: thunderous
|
| posted on March 30th, 2012 at 09:42 AM |
|
|
Geeez u been a busy boy!! Will be keeping an eye on this build (Hurry up i wanna see more)
"If at first you don't succeed, skydiving is not for you." - Anonymous  |
|
|
VDUBXTC
A.k.a.: Jace
Wolfsburg Elder
Tea Bag
Posts: 3587
Threads: 678
Registered: February 21st, 2003
Member Is Offline
Location: Somewhere on the South side Brissy QLD
Theme: UltimaBB Pro Navy
Mood: swept off my feet by an Ang3l
|
| posted on March 30th, 2012 at 07:53 PM |
|
|
oval was from georgetown???
|
|
|
D-train
Seriously Crusin Dubber
Posts: 180
Threads: 40
Registered: October 2nd, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 30th, 2012 at 08:42 PM |
|
|
| Quote: | Originally
posted by VDUBXTC
oval was from georgetown???
|
That's the one, sittin for quite a while as well, how did u know about it livin in brisbane?
|
|
|
VDUBXTC
A.k.a.: Jace
Wolfsburg Elder
Tea Bag
Posts: 3587
Threads: 678
Registered: February 21st, 2003
Member Is Offline
Location: Somewhere on the South side Brissy QLD
Theme: UltimaBB Pro Navy
Mood: swept off my feet by an Ang3l
|
| posted on April 1st, 2012 at 04:45 PM |
|
|
| Quote: | Originally
posted by D-train
| Quote: | Originally
posted by VDUBXTC
oval was from georgetown???
|
That's the one, sittin for quite a while as well, how did u know about it livin in brisbane?
|
I've known of it for many years. Had the option of taking it home with an old country buggy from there when he was having a yard clean up after
council had a spit.
Did you ever see the 55 ragtop oval he had there in the old run down shed many years ago. Japanese bloke picked that one up. its now in the USA.
I'm a newi boy. only been in brissy the last 6 years
|
|
|
D-train
Seriously Crusin Dubber
Posts: 180
Threads: 40
Registered: October 2nd, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 1st, 2012 at 06:29 PM |
|
|
i wish i saw that one, i remember all his cars as a young kid b4 they all got sold an scrapped, he had some treasure...
after the wknd of driving an beer, a couple of things done, notched spring plates an painted.
beam painted an half assembled
paintin up the front end bits, before the k&ls get rebuilt with dropped spindles in them.
hopefully some more 2moro
|
|
|
dubstar
Learner Dubber
Posts: 5
Threads: 0
Registered: December 22nd, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 2nd, 2012 at 01:25 PM |
|
|
Coming along nicely |
|
|
D-train
Seriously Crusin Dubber
Posts: 180
Threads: 40
Registered: October 2nd, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 2nd, 2012 at 08:07 PM |
|
|
been fuckin around a little 2day, doin stuff to the chassis, but finally got the bracket for the engine made, so fram an oiler bottle is hoked up, an
tried to start it, but no dice yet... trouble shoot now
|
|
|
5lam
A.k.a.: Dave
Wolfsburg Wizard
AKA: BlackBug
Posts: 520
Threads: 38
Registered: March 19th, 2006
Member Is Offline
Location: Gold Coast, QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: Slammed
|
| posted on April 3rd, 2012 at 07:58 AM |
|
|
Good to meet you yesterday, bud! Pretty jealous of your little collection!
[size=5]Custom doesn't come in a Box[/size]
|
|
|
68Volkaru
Slammed & Awesome Dubber
Posts: 80
Threads: 9
Registered: April 17th, 2011
Member Is Offline
Location: Queanbeyan,NSW
Theme: UltimaBB Pro Purple
Mood: Depends on the Kids!
|
| posted on April 12th, 2012 at 09:27 PM |
|
|
Love the progress so far.
"Subscribed"
Cant wait to see the outcome.
Understeer is when you hit the wall with the front of the car. Oversteer is when you hit the wall with the rear of the car.
Horsepower is how fast you hit the wall. Torque is how far you take the wall with you. |
|
|
D-train
Seriously Crusin Dubber
Posts: 180
Threads: 40
Registered: October 2nd, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 22nd, 2012 at 04:25 PM |
|
|
| Quote: | Originally
posted by BlackBug
Good to meet you yesterday, bud! Pretty jealous of your little collection!
|
nice to meet u as well dave, ur ride is lookin good...
been fuckin around for the last couple of days...
4" dub beam
2 1/2' droppers
old nose cone bushes
new ones in
original split box
puttin together
beam together with spindles
rims on for now
now for car sounds an pretend its running...
oh wait...
it is running
couple of vids of it starting off 6v.
http://www.youtube.com/watch?v=ckHERGvb6Ss&feature=youtu.be
http://www.youtube.com/watch?v=mfHN60NGf6M&feature=youtu.be
http://www.youtube.com/watch?v=BSzc2usrKLA&feature=youtu.be
alls thats needed is the solid brake lines an the chassis is done!!! hopefully have the engine on the chassis this week.
|
|
|
D-train
Seriously Crusin Dubber
Posts: 180
Threads: 40
Registered: October 2nd, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 14th, 2012 at 06:03 PM |
|
|
been home a day an macca an dork gave me a lift with the engine to the pan...
an then this happened..
http://www.youtube.com/watch?v=y-eibPk_UKA&feature=youtu.be
been silly
http://www.youtube.com/watch?v=tfrK4edrZt8&feature=youtu.be
burnout time..
http://www.youtube.com/watch?v=Dx9xvtfcwDk&feature=youtu.be
this arrived in the mail.
and finally gettin around to gettin the panels to start them
some shit done...
all the cables/lines an fuel hooked up finally...
so burn out time it was..
new fuel fillter as well
an some vids..
boost gauge not under load
http://www.youtube.com/watch?v=Ncn7sB2PSgI&feature=youtu.be
http://www.youtube.com/watch?v=-QuWIJG8cRg&feature=youtu.be
http://www.youtube.com/watch?v=yOzS5shPOmI&feature=youtu.be
|
|
|
68Volkaru
Slammed & Awesome Dubber
Posts: 80
Threads: 9
Registered: April 17th, 2011
Member Is Offline
Location: Queanbeyan,NSW
Theme: UltimaBB Pro Purple
Mood: Depends on the Kids!
|
| posted on May 14th, 2012 at 06:33 PM |
|
|
Awesome. Great vids.... That last one was like i had a bad batch of mushies . (Or should i say a good batch?)
Am hangen to see what you do with the shell.
Understeer is when you hit the wall with the front of the car. Oversteer is when you hit the wall with the rear of the car.
Horsepower is how fast you hit the wall. Torque is how far you take the wall with you. |
|
|
69bug
Officially Full-On Dubber
Posts: 300
Threads: 24
Registered: January 21st, 2012
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 14th, 2012 at 07:49 PM |
|
|
Great build !
1969 1500
|
|
|
 MISS VDUB
A.k.a.: Ash
Super Administrator
Mrs KOMBIBOB
Posts: 2565
Threads: 96
Registered: September 20th, 2005
Member Is Offline
Location: Beautiful Sunshine Coast, QLD
Theme: UltimaBB Pro White
Mood: Low down and Dirty
|
| posted on May 14th, 2012 at 08:29 PM |
|
|
Aren't you finished yet? 
1963 Single Cab Ute: "El Concreto"
1962 Baja Beetle: "Peanut"
1968 Porsche 912 SWB: "Pip"
1972 Kombi Snail: "The Snail"
2012 Skoda Octavia Scout: "Scout"
2016 Scirocco R: "Rocco"
|
|
|
JohnnyMac
Slammed & Awesome Dubber
Posts: 80
Threads: 7
Registered: April 24th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 14th, 2012 at 10:03 PM |
|
|
Very cool build mate, looking forward to seeing it all come together 
|
|
|
D-train
Seriously Crusin Dubber
Posts: 180
Threads: 40
Registered: October 2nd, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 15th, 2012 at 06:06 PM |
|
|
| Quote: | Originally
posted by MISS VDUB
Aren't you finished yet?
|
I'll only be finished when u an bob are behind me eatin my dust!!
Haha
|
|
|
MISS VDUB
A.k.a.: Ash
Super Administrator
Mrs KOMBIBOB
Posts: 2565
Threads: 96
Registered: September 20th, 2005
Member Is Offline
Location: Beautiful Sunshine Coast, QLD
Theme: UltimaBB Pro White
Mood: Low down and Dirty
|
| posted on May 15th, 2012 at 06:15 PM |
|
|
Only dust we will be eating is from the wind blowing off the pan and motor in your shed. The cobwebs and spiders are more likely to get us first 
1963 Single Cab Ute: "El Concreto"
1962 Baja Beetle: "Peanut"
1968 Porsche 912 SWB: "Pip"
1972 Kombi Snail: "The Snail"
2012 Skoda Octavia Scout: "Scout"
2016 Scirocco R: "Rocco"
|
|
|
D-train
Seriously Crusin Dubber
Posts: 180
Threads: 40
Registered: October 2nd, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 16th, 2012 at 12:07 PM |
|
|
Ooooohhhhhh....... Now that's more incentive to get this thing goin.. I'll lighten it where I can with fiberglass an a whale tail to keep the back
down in the race. Haha
|
|
|
5lam
A.k.a.: Dave
Wolfsburg Wizard
AKA: BlackBug
Posts: 520
Threads: 38
Registered: March 19th, 2006
Member Is Offline
Location: Gold Coast, QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: Slammed
|
| posted on May 16th, 2012 at 02:08 PM |
|
|
| Quote: | Originally
posted by D-train
Ooooohhhhhh....... Now that's more incentive to get this thing goin.. I'll lighten it where I can with fiberglass an a whale tail to keep the back
down in the race. Haha
|
Things like that shouldn't even be spoken about in Jest!
[size=5]Custom doesn't come in a Box[/size]
|
|
|
| Pages: 1 2 3 .. 6 |
