| [ Total Views: 688 | Total Replies: 8 | Thread Id: 96938 ] |
|
|
 moonlite6t6beetle
A.k.a.: Corey Marriott
Officially Full-On Dubber
Posts: 355
Threads: 80
Registered: February 18th, 2003
Member Is Offline
Location: Northam WA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 16th, 2012 at 01:31 AM |
|
|
clutch issues on 1200 to 1835 swap (job happening now)
Hey all,
Have just done an engine swap on my partners 62.
Had the old 1200 gearbox, ground out the bellhousing, created the flywheel clearance, swapped the 6v to 12v starter.
Fitted a high performance clutch from VW centre in WA (supplied and trusted) to suit the early style throw out bearing.
Bolted the engine in, running fine. no unusual noises. all very sweet.
had a bit of slack on the clutch cable visually from the wingnut to the leaver.
pressed the clutch and really felt like we had nothing.
could swing the release bearing arm from the outside of the gearbox to about -40degrees before it seemed like it was touching anything..?
i tentioned the cable to about 3/4 its potential length. pulling the arm to about -25degrees. but seemed like i was going to have nothing any which
way.
I pulled the motor out suspecting to find the release bearing had dropped or the flat plate on the clutch had come unclipped.. but everything seems
okay.?!
Anyone know what might be up?
Do i need a shorter clutch cable??
I mean that arm leaning back on a -40degree constant seemed strange to me?
This job is happening right now, so standing by if anyone else is up at such a ridiculous hour.
Thanks fellas
Moonlite... 54 and 66 beetle
|
|
|
Ldog
Commited Dubber
Posts: 70
Threads: 19
Registered: May 23rd, 2011
Member Is Offline
Theme: UltimaBB Pro Orange
Mood: insomnia
|
| posted on May 16th, 2012 at 02:28 AM |
|
|
does the pressure plate have the ring in the centre?
1915,c95,44's,44x37.5,NA, DuBwAy
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on May 16th, 2012 at 08:30 AM |
|
|
x2, sounds like no running ring on the pressure plate, the early trans requires this. damn trusted suppliers. 
Clutch lever that the cable attaches to will be near vertical, and is in adjustment with about 2mm of fwd movement before the throw-out contacts the
running ring.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
Camo
A.k.a.: Kev
Custom Title Time!
Posts: 1936
Threads: 209
Registered: October 29th, 2007
Member Is Offline
Location: Sydney - Liverpool area
Theme: UltimaBB Pro Blue
|
| posted on May 16th, 2012 at 08:44 AM |
|
|
You said, "to suit the early style throw out bearing". I take it from this you have the removable pad on the pressure plate, but did you get a new
throw out bearing that may be for the later style. Apparently they are about 15mm difference in thickness overall.
Kev
|
|
|
moonlite6t6beetle
A.k.a.: Corey Marriott
Officially Full-On Dubber
Posts: 355
Threads: 80
Registered: February 18th, 2003
Member Is Offline
Location: Northam WA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 28th, 2012 at 06:41 PM |
|
|
So the award for strange knowledge goes to camo for his 15mm thickness on the later style throw out bearing.
Swapped it, and readjusted.. and i must say (matt> I still had a great
deal of adjustment requirement before i felt the throw out contact the pressure plate.
now about -25degrees. But everything has been operating just fine so even though im well over half way on my cable adjustment, the clutch feels great
and is highly operatable.
She is a quick ole' girl now, may i just say it.
happy times.
Moonlite... 54 and 66 beetle
|
|
|
jamiesc
Wolfsburg Wizard
Posts: 559
Threads: 106
Registered: December 30th, 2010
Member Is Offline
Location: bayside brisbane
Theme: UltimaBB Pica Red
|
| posted on May 28th, 2012 at 08:56 PM |
|
|
try ajusting your clutch arm that comes out of your gearbox a couple of degrees or even put washers for a temporary fix but i done this for a year and
buy a new clutch cable i had to do this to mine.
cheers jamie
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on June 1st, 2012 at 03:56 PM |
|
|
^ you can't turn the arm on the shaft. the splines are only on one side of the shaft.
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
jamiesc
Wolfsburg Wizard
Posts: 559
Threads: 106
Registered: December 30th, 2010
Member Is Offline
Location: bayside brisbane
Theme: UltimaBB Pica Red
|
| posted on June 2nd, 2012 at 12:42 PM |
|
|
aww yeah thats right but i did have to use some washers for a while until i could be bothered to fix it properly
|
|
|
moonlite6t6beetle
A.k.a.: Corey Marriott
Officially Full-On Dubber
Posts: 355
Threads: 80
Registered: February 18th, 2003
Member Is Offline
Location: Northam WA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 5th, 2012 at 06:28 PM |
|
|
what was your motor conversion jamiesc? curiosity with that mental looking profile pic
Moonlite... 54 and 66 beetle
|
|
|
