| [ Total Views: 802 | Total Replies: 6 | Thread Id: 99899 ] |
|
|
 nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on November 29th, 2012 at 09:43 PM |
|
|
Broken flywheel dowell pins
Anybody ever broken them and found an easy way to get the bits out of the crankshaft? I have been over an hour and managed to only get 2 out so far- 6
still to go.
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on November 30th, 2012 at 04:52 AM |
|
|
always hard to get out there tough
|
|
|
dangerous
A.k.a.: Dave Butler Muffin Man
23 Windows of Awesome
Posts: 5901
Threads: 178
Registered: January 6th, 2005
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
Mood: 591
|
| posted on November 30th, 2012 at 05:12 AM |
|
|
Bummer!
I have done the same and we had to drill them out.
Most dowels are case gardened so the core is softer,
but some are through hardened and can be a pain.
The ones I had to do were thru hardenned and I needed to us a tungsten tip concrete drill, sharpened up.
The other option is some carefull tig welding of a lug on there for a slide hammer.
| Quote: | Originally
posted by westi
That's mad Alan.
|
|
|
|
HappyDaze
A.k.a.: Greg Mackie
Son of Jim - Creator of Good
Superannuated
Posts: 2887
Threads: 141
Registered: June 13th, 2009
Member Is Offline
Location: Southern Highlands NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy enough
|
| posted on November 30th, 2012 at 05:16 AM |
|
|
The masonry drill ^ is worth a try........but how did you manage to bust 'em, Garry??????
I'd rather wear a Beetle out by racing it than by polishing it!
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on November 30th, 2012 at 05:30 AM |
|
|
| Quote: | Originally
posted by HappyDaze
The masonry drill ^ is worth a try........but how did you manage to bust 'em, Garry??????
|
. Still trying to figure out what happened. Have done a fair bit of damage. New convertor and crank hub are rooted,but have
started on another hub and will run a standard convertor to get me racing. Been talking to Aaron(20b) and I will open the buggered one up and have a
go at repairing it. Have run the engine to bed the cam and rings and was almost needing a blood transfusion- had a bit of activity in the front of my
shorts.
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on November 30th, 2012 at 05:38 AM |
|
|
Thanks for the tip Dave. The 2 I have got out so far are a lot softer in the gutz-but still quite hard.will get back into it tonight. You will
probably hear the vocabulary full of " F " words from your place.
|
|
|
dangerous
A.k.a.: Dave Butler Muffin Man
23 Windows of Awesome
Posts: 5901
Threads: 178
Registered: January 6th, 2005
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
Mood: 591
|
| posted on November 30th, 2012 at 07:12 AM |
|
|
Yeah, last one I did took me a whole day.
The one I experienced sheared on the dyno.
The gland nut also self tightened when it sheared,
so we were unaware of it until we were trying to remove the dyno hub.
Sounds like yours came loose.
When our crank was nitrided it softened the case hardened dowel, and it was not up to the torque capacity.
The new replacement scat dowels, once fitted, never had a problem after that.
Nitriding is normally around 560 degrees, which tempered the dowel to its core,
leaving only the thin layer of nitrided metal,
in the area that was exposed.
| Quote: | Originally
posted by westi
That's mad Alan.
|
|
|
|
