Skip to content
Aussieveedubbers

Splitty Rear Wheel Bearings

0 likes
Share Share on Facebook Share on X Share on Reddit

PurpleT3 Fahrvergnugen

880 posts · joined Apr 2003 ·

#454532
It appears that the rear wheel bearing on the splitty ('67) is leaking oil. The oil is getting onto the inside of the backing plate. I have disassembled the brakes. How do you get the backing plate and bearing cover off? Haven't got a manual yet, so I cann't look it up.
Ain't nothin' like the wind in your hair.

vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 ·

#454536
undo the bolts and nuts that attach it
very easy
I read it on FACEBOOK so it must be true


http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630


http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099


http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603


http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409

PurpleT3 Fahrvergnugen

880 posts · joined Apr 2003 ·

#454541
Done that, but it doesn't want to come off. Do I need a puller, or should it come off more easily.
Ain't nothin' like the wind in your hair.

geodon Wolfsburg Wizard

478 posts · joined Aug 2002 ·

#454557
Unusual. Try some heat to expand the cover- even if it's a hair drier or hot air gun. I think the bearings sit a little proud in the housing & it may be stuck in the cover. If u use a screwdriver to lever it off be careful not to scratch the faces.

Menangler Custom Title Time!

1,991 posts · joined Aug 2002 ·

#454585
Don't forget the bolt that holds the wheel cylinder, it also holds the backing plate, then the dowels down the bottom.
FAHRVERGNUGEN;
Description of a pleasurable sensation,
Experienced when a car and it's driver are in mutual harmony, A unique driving experience, Pleasure, Satisfaction,
A feeling experienced by Volkswagen Drivers.

vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 ·

#454722
As Dave said undo them all n grab it n rattle it all about just like doing the Hokie Pokie ...
I read it on FACEBOOK so it must be true


http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630


http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099


http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603


http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409

PurpleT3 Fahrvergnugen

880 posts · joined Apr 2003 ·

#454736
Thanks guys. Got if off. Heated it up, then wiggled with two screw drivers until it popped off the bearing. All painted up, just need a new seal kit to put it all back together.
Ain't nothin' like the wind in your hair.

vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 ·

#454738
make sure the O rings are seated properly when fitting n use the paper gaskets as well otehr wise you get an Oil dripper

Did you drain the reduction boxes while you have it apart and gear box oil as well.
I read it on FACEBOOK so it must be true


http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630


http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099


http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603


http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409

PurpleT3 Fahrvergnugen

880 posts · joined Apr 2003 ·

#454740
I couldn' avoid draining the reduction hubs. As soon as I loosened the bearing cover, oil started pouring out. I have some 90w Hypoid gear oil in the garage. Is this the right grade to refill the hubs?
Ain't nothin' like the wind in your hair.

Menangler Custom Title Time!

1,991 posts · joined Aug 2002 ·

#454767
Yes
FAHRVERGNUGEN;
Description of a pleasurable sensation,
Experienced when a car and it's driver are in mutual harmony, A unique driving experience, Pleasure, Satisfaction,
A feeling experienced by Volkswagen Drivers.