Skip to content
Aussieveedubbers

stock idle air screw position?

0 likes
Share Share on Facebook Share on X Share on Reddit

Anthiron The Baja Rejuvenation Begins

4,936 posts · joined Oct 2003 ·

#460081
on a 30pict 2 solex how many turns out is the stock position?
62/60 model bug eye baja bug, (Full Build in Progress)
1974 Chevrolet Luv
1970 MK2 Ford Cortina GT
1979 Yamaha RX125 Two Stroke tracker project.
2004 Harley Davidson Sportster XL Custom

oval TOFU Bitte, ein Bit!

2,946 posts · joined Jul 2003 ·

#460084
2.5 i think, then you adjust from there by listening to the revs...

[ Edited on 1-3-06 by oval TOFU ]
...and Robert's ya father's brother...

geodon Wolfsburg Wizard

478 posts · joined Aug 2002 ·

#460090
Does the 30 pict have an air screw? I thought only that heathen 34 pict had one of those.
If u r referring to the volume control screw, i think u turn it clockwise till it seats LIGHTLY then back it off about 1.5 turns. Start up & warm it up then turn it in till the eng idle speed dies then out till it only just picks picks up speed again. Then re-set the idle speed screw to the idle speed u want. I lurve those old carbies! Esp my beloved 28pci on my SC

Anthiron The Baja Rejuvenation Begins

4,936 posts · joined Oct 2003 ·

#460096
cheers fellas.
62/60 model bug eye baja bug, (Full Build in Progress)
1974 Chevrolet Luv
1970 MK2 Ford Cortina GT
1979 Yamaha RX125 Two Stroke tracker project.
2004 Harley Davidson Sportster XL Custom

ACE_76

Former member ·

#460242
With 3 carbs (all 34 Pict-4's) on 3 different motors (1600 - 1640) I've found the idle mixture screw to always require more turns out than the manual says, generally over 3, to a bit over 4, instead of the supposed 2.5 - 3. (Earlier carbs recommended less turns out.)
You'll hear when it's happy. Too lean: speed drops. Screw it out- speed increases. Keep going & speed drops as mix becomes too rich. Can set for max. speed, or slightly in from that point.
Don't set idle mixture too lean!

vw54 Administrator Always Waiting 4 Friday

16,723 posts · joined Aug 2002 ·

#460280
There is No stock position all engines will vary slightly

If you have over haulled the carby then screw it out bout 3 full turns for start up then allow the engine to warm up and adjust as per above
I read it on FACEBOOK so it must be true


http://forums.aussieveedubbers.com/viewtopic.php?tid=91278&page=1#pid848630


http://forums.aussieveedubbers.com/viewtopic.php?tid=63561&page=1#pid624099


http://forums.aussieveedubbers.com/viewtopic.php?tid=4832&page=1#pid452603


http://forums.aussieveedubbers.com/viewtopic.php?tid=60650&page=1#pid574409

Anthiron The Baja Rejuvenation Begins

4,936 posts · joined Oct 2003 ·

#460315
basically id just been adjusting on feel of the engine revs.

was just wondering where the books say it should be from the factory as a light guide line.
62/60 model bug eye baja bug, (Full Build in Progress)
1974 Chevrolet Luv
1970 MK2 Ford Cortina GT
1979 Yamaha RX125 Two Stroke tracker project.
2004 Harley Davidson Sportster XL Custom