door cards,vynal,shallow staples..

simoninoz Seriously Crusin Dubber

161 posts · joined Jan 2005 · 14 May 2006, 2:59 pm

#488386

Right, got orginal pair of t3 door cards and want to remount them. Easy eh. Want to do it like it was from the factory with shallow staples to suit depth of modern mdf but only thing that seems commercially avaliable, at bunnings etc, are to deep. Anyone know of alternatives?
Also glue - solvent based ruins the vynal, what's a good alternative? Craft glues are just shite and don't work. Tired or trial and error now, anyone got this down pat??
Cheers

bugeyedbabe Wheres her VW heart on her sleeve

3,945 posts · joined Jan 2005 · 14 May 2006, 4:26 pm

#488400

i did mine...and what we did was this...

spray adhesive (strong hold) from bunnings...to spray on the front. Then wipe the fron down to stop and wrinkles....
Pull round the back nice and tight...
Then to be really sure...I used a hot glue gun around the edges on the back...between edge fo the board and the holes marked out.
And finally use the staple gun...we got ours from a craft shop (they had the shallow staples...but not 100% sure where...will check with person who bought it at the time)
When its all done and died...then u trim it up nicely...and use the spray adhesive again to keep the edges nice and neat..and down...

It became a little bit of work, but is well worth it. And it was based on what i could see was done at the factory.

hope it helps

Cheers
Beb

dubless. 🥲
🥷 And who the helled parked the Mitsubishi "Prancer" under my house??? 🥷

$2.63 homebrand baja

0 posts · joined Feb 2004 · 14 May 2006, 4:40 pm

#488403

❗ ahh, craft shop, I have been wondering about the shallow staples too, thanks beb 😉 how did you attach the little metal clip things?

65busser Moderator Custom Title Time!

1,795 posts · joined Nov 2002 · 14 May 2006, 8:58 pm

#488537

Simon,
The staples you want are 5/32". You'll need to use a staple gun, but MDF will not take the staples. You'll need to use masonite, just like VW did.
Best glue is a brush on upholstery/trimming adhesive, but for the amount you need, you may as well buy some Selleys Gel Grip from Bunnings. Gel grip will hold and it's easy to use 'cos it's a gel and not a liquid.
If you've got a staple gun I'll send you a few hundred of the correct staples.
Brad

www.busnbug.com

simoninoz Seriously Crusin Dubber

161 posts · joined Jan 2005 · 16 May 2006, 12:30 pm

#489119

65busser wrote:Simon,
The staples you want are 5/32". You'll need to use a staple gun, but MDF will not take the staples. You'll need to use masonite, just like VW did.
Best glue is a brush on upholstery/trimming adhesive, but for the amount you need, you may as well buy some Selleys Gel Grip from Bunnings. Gel grip will hold and it's easy to use 'cos it's a gel and not a liquid.
If you've got a staple gun I'll send you a few hundred of the correct staples.
Brad

Thanks Brad for that offer, I'll have a look up here. Yeah did buy semi pro stapler from Bunnings for this job so hope these lit'luns fit it.

Thanks all.

simoninoz Seriously Crusin Dubber

161 posts · joined Jan 2005 · 16 May 2006, 12:32 pm

#489121

bugeyedbabe wrote:i did mine...and what we did was this...

spray adhesive (strong hold) from bunnings...to spray on the front. Then wipe the fron down to stop and wrinkles....
Pull round the back nice and tight...
Then to be really sure...I used a hot glue gun around the edges on the back...between edge fo the board and the holes marked out.
And finally use the staple gun...we got ours from a craft shop (they had the shallow staples...but not 100% sure where...will check with person who bought it at the time)
When its all done and died...then u trim it up nicely...and use the spray adhesive again to keep the edges nice and neat..and down...

It became a little bit of work, but is well worth it. And it was based on what i could see was done at the factory.

hope it helps

Cheers
Beb

Thanks, will that too.