| [ Total Views: 609 | Total Replies: 7 | Thread Id: 105355 ] |
|
|
 donovan
Seriously Crusin Dubber
Posts: 136
Threads: 37
Registered: April 7th, 2009
Member Is Offline
Location: sunshine coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 9th, 2014 at 06:50 AM |
|
|
72 notch rotors
just wondering if it is correct vw used porsche 914 brakes on the 72/3 type 3. if so what is the min rotor thickness for rwc in qld. mine are 8.5mm
and 9mm
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on March 11th, 2014 at 02:30 AM |
|
|
In the latest volks world mag the buying guide says they use generic Beetle brakes up front.
As for min thickness it depends on the as new thickness but 8.5 doesn't sound great. Most manufacturers allow 1-1.5mm wear.
madness is in the eye of the beholder  |
|
|
cb john
Wolfsburg Wizard
Posts: 470
Threads: 6
Registered: June 22nd, 2007
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue
|
| posted on March 11th, 2014 at 05:52 PM |
|
|
| Quote: | Originally
posted by donovan
just wondering if it is correct vw used porsche 914 brakes on the 72/3 type 3. if so what is the min rotor thickness for rwc in qld. mine are 8.5mm
and 9mm
|
911, 912,and 4 cyl 914 thickness of solid front disk is 12.7 / 12.5 mm, minimum on the front is 11.0 mm
On type 3 with generic disks is thickness 9.5 / 9.45 , min. 8.0 mm
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on March 11th, 2014 at 07:02 PM |
|
|
its the diameter you go to worry about here. the 72 up had larder diameter rotors.
278 vs 281mm
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on March 11th, 2014 at 08:42 PM |
|
|
| Quote: | Originally
posted by psimitar
As for min thickness it depends on the as new thickness but 8.5 doesn't sound great. Most manufacturers allow 1-1.5mm wear.
|
Pfffft, that's just a suggestion
| Quote: | Originally
posted by vlad01
its the diameter you go to worry about here. the 72 up had larder diameter rotors.
278 vs 281mm
|
That's what I'm running on my bug now off a 73 I parted out, havent had any clearance issues.
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on March 12th, 2014 at 01:51 PM |
|
|
I think the clearance isn't the issue as most calipers allow more that this difference. The issue I would be worried about is running the smaller
disks and the pads running off the edge.
depending on the setup, some cars run the pads right to the edge. So pads running a mm or 2 over the edge, would be a bit dodgy.
but its could be fine for what you know. I personally haven't tried it.
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on March 12th, 2014 at 02:50 PM |
|
|
You could chamfer the edge of the pad, only talking about 2MM
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on March 12th, 2014 at 07:58 PM |
|
|
yeah thats true
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
