Board Logo
Go To Bottom

Printable Version  
[ Total Views: 1008 | Total Replies: 4 | Thread Id: 112703 ]
Author: Subject:  Measure Bore without pulling heads off?
Membermossman
Commited Dubber
**


No Avatar


Posts: 73
Threads: 30
Registered: April 6th, 2013
Member Is Offline

Theme: UltimaBB Pro Blue ( Default )

posted on August 14th, 2017 at 08:39 PM
Measure Bore without pulling heads off?


Hi Guys,
does anyone know of a way to internally measure the size of a cylinder bore and stroke (to determine engine size) without dismantling an engine? Is there some small laser/3D imaging tool or camera that can be inserted in the spark plug hole?
My T1 engine number suggests it is a 1600 but I suspect it is bigger.
Cheers
Super ModeratorBizarre
Super Moderator
The artist formerly known as blue74l
*******

Rank Avatar

Avatar


Posts: 12736
Threads: 730
Registered: August 25th, 2002
Member Is Offline

Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )

posted on August 14th, 2017 at 09:53 PM



I do not know of any way other than using a ruler



Futue te ipsum!!!
Memberadlbeetle66
A.k.a.: Denver
Custom Title Time!
Under the car.........again!
*****


Avatar


Posts: 1476
Threads: 98
Registered: August 15th, 2014
Member Is Offline

Location: Capalaba, Brisbane, QLD
Theme: UltimaBB Streamlined2
Mood: ICH BIN VW NUSS

posted on August 14th, 2017 at 10:09 PM



I would think that you could measure the stroke by putting something long (e.g. a push rod) down the spark plug hole and mark the two most extreme points of the stroke on the rod
Measure the distance between those two points and you have your stroke length?
Hope that makes sense.
Memberbevoracing
A.k.a.: Tony Beven
Officially Full-On Dubber
***


Avatar


Posts: 324
Threads: 35
Registered: January 18th, 2009
Member Is Offline

Location: Mount Pleasant SA
Theme: UltimaBB Vintage
Mood: Leaning against the shed wall !.

posted on August 15th, 2017 at 03:40 PM



Years ago I saw a go kart scrutineer test capaity by connecting a machine to the spark plug hole and spinning the engine. Perhaps talk to a go kart racer?



Country Buggy King & Link Pin Overhauls, Type 1 & 2 King Pins, General Machining.
http://forums.aussieveedubbers.com/viewtopic.php?tid=74138 
My car is KO813
Memberpsimitar
Son of Jim - Creator of Good
******


Avatar


Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline

Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue

posted on August 16th, 2017 at 12:02 PM



You could get a piston at the bottom of it's travel, disconnect the rockers for that piston so as to close the valves and then fill the cylinder with a thick enough liquid that won't quickly seep past the rings. Then you'd have the volume of a cylinder. Then divide by the stroke of the piston back to TDC and you get the area of the piston.
If you can figure a way to do that with compressed air then probably be the cleaner way to figure it out. Otherwise, as with any engine (even non-AC) you have to remove a head to measure things.




madness is in the eye of the beholder :yes:


  Go To Top


Powered by GaiaBB, © 2011 The GaiaBB Group


[ Queries: 40 ] [ PHP: 2.5% - SQL: 97.5% ]