| [ Total Views: 574 | Total Replies: 5 | Thread Id: 18640 ] |
|
|
 graeme86
Casual Dubber
Posts: 23
Threads: 6
Registered: December 5th, 2002
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
 posted on February 7th, 2004 at 06:23 PM |
|
|
Weber IDF problem??
I have dual 40IDFs. Current issue is: whilst idling, one cylinder thoat can be blocked off at the air horn with no effect on the idle speed of the
engine. The idle mixture screw for that cylinder also has no effect. The idle speed is steady however. Also RAW, and I mean RAW fuel is coming out of
the exhaust pipe - enough to wet the ground where the exhaust points to! Spark is present at that cylinder. I have replaced the
following:points,plugs,dizzy cap,leads,coil and carbs have been professionally soaked, cleaned and blown out. Any ideas? Help!!!!
|
|
|
Menangler
A.k.a.: Dave Becker
Custom Title Time!
Posts: 1991
Threads: 309
Registered: August 26th, 2002
Member Is Offline
Location: South Coast NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 7th, 2004 at 07:19 PM |
|
|
Have you done a compression test on that cylinder?
FAHRVERGNUGEN;
Description of a pleasurable sensation,
Experienced when a car and it's driver are in mutual harmony, A unique driving experience, Pleasure, Satisfaction,
A feeling experienced by Volkswagen Drivers.
 |
|
|
graeme86
Casual Dubber
Posts: 23
Threads: 6
Registered: December 5th, 2002
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 7th, 2004 at 08:52 PM |
|
|
Yes. 137 psi. Other cylinders were 132 , 138, and 142. Engine has 8.0 to 1 compression and is ~55000km old
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12780
Threads: 734
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 8th, 2004 at 03:03 PM |
|
|
What happens when you pull the pair lead for that plug??
ie IF it is #1 that you think has the problem and you pull the lead to #2 does the motor die??
What happens when you rev it??? Does it come alive???
When you pull THAT plug is it wet??
Did it run better before??? or is this a new installation???
Carbs were soaked but were the jets???
Futue te ipsum!!!
|
|
|
graeme86
Casual Dubber
Posts: 23
Threads: 6
Registered: December 5th, 2002
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 8th, 2004 at 05:33 PM |
|
|
I'll try that pair trick and see what happens and report back. Bit late now unfortunately...may upset the neighbours. These carbs have been on
this engine for about 12 years now actually. I had a backfire up a carb (just one of those occassional Weber pops you get) which set fire to the air
cleaner (that was fun!) and its all gone pear shaped since then. The carb that caught fire was on 1 & 2 cylinder bank. I am having trouble with
#4 throat. They have been totally cleaned out to make sure nothing was stuck in them since that "fateful incident". It runs pretty good
over about 2500rpm which suggests to me something in the idle circuit. Thanks for the feedback so far.
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12780
Threads: 734
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 8th, 2004 at 07:03 PM |
|
|
| Quote: | Originally
posted by graeme86
It runs pretty good over about 2500rpm which suggests to me something in the idle circuit.
|
HAS to be idle circuit.
Just a matter if jet or passage.
Futue te ipsum!!!
|
|
|
graeme86
Casual Dubber
Posts: 23
Threads: 6
Registered: December 5th, 2002
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 13th, 2004 at 09:25 PM |
|
|
Just a follow up to this...FYI I think I found the problem...the coiled up return spring on the throttle plate appears to have been jammed between
the manifold and the carby. It just sits at a slight angle and is thicker than the distance from the throttle shaft to the base of the carby..so if it
is not held straight up to clear the manifold, it holds the carby slightly off the manifold when tightened up...causing the massive air leak. Seems to
run quite nicely now!
|
|
|
