| [ Total Views: 1751 | Total Replies: 6 | Thread Id: 58872 ] |
|
|
 ElusiveStranger
Officially Full-On Dubber
Posts: 330
Threads: 30
Registered: May 28th, 2006
Member Is Offline
Location: Kent. England
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 16th, 2006 at 06:33 AM |
|
|
Heating in Buses
Now it's getting chilly in Ol' Blighty I've started on my heating. Electric blankets don't demist windscreens 
Decided to go for a Mk 3 Golf (Rabbit?) heater matrix between the two cab seats. 3" hole cut in the floor and a 'stove pipe' to connect to the orig
hot air pipe. Will be using either a squirrel cage fan to blow air through this, or a bilge fan to suck the air through.
My van had a storage box fitted between the seats so the walktrough wasn't lost.
Would you guys please post some photos of your heating set ups please?
Cheers 
|
|
|
kevo
A.k.a.: kevo Milner
Officially Full-On Dubber
Posts: 371
Threads: 53
Registered: March 22nd, 2005
Member Is Offline
Location: wanneroo, perth WA
Theme: UltimaBB Psyche Green
Mood: always happy
|
| posted on December 16th, 2006 at 12:40 PM |
|
|
this keeps me very warm on even the coldest days haha,
all i have to do is just open the normal front vents and in comes the hot air
On hot days i close the vents and its fine (for a car without air con that is...)
[ Edited on 16/12/2006 by kevo ]
76 baywindow kombi - V8 & Weddle racing diff and gearbox
Daily driven beach cruiser
|
|
|
71EJVan
Officially Full-On Dubber
Posts: 352
Threads: 23
Registered: August 19th, 2005
Member Is Offline
Location: Central Coast NSW, Australia
Theme: UltimaBB Pro White
|
| posted on December 16th, 2006 at 09:33 PM |
|
|
I'm mounting a heater core from a Holden Rodeo truck up under the floor just behind the front beam. I has a bypass vane so the blower behind it will
also push fresh air. Will hook up to the original pipework forward.
Brendan
A VW for everyone!!
1972 1302 German Look
1971 Bay Panel with Subaru EJ20T
1970 Type 3 squareback in progress
1971 Type 3 notchback in progress
|
|
|
ElusiveStranger
Officially Full-On Dubber
Posts: 330
Threads: 30
Registered: May 28th, 2006
Member Is Offline
Location: Kent. England
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 17th, 2006 at 01:16 AM |
|
|
Kevo, that made me laugh, thanks. I haven't got aircon for the summer.
You guys are lucky as you can put the rad up front, add some roo bars and your buses look well hard
I'm loving your Baja buses but I don't think it'd look good over here.
Brendon, I did wonder about that sort of set up but have heard that due to the low pressure under the bus it may try and 'suck' the air from inside
the bus. I don't know if this is correct. How's yours going?
Thanks guys
|
|
|
GeorgeL
Officially Full-On Dubber
Posts: 231
Threads: 11
Registered: February 5th, 2006
Member Is Offline
Location: 7200 miles off the Queensland coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 17th, 2006 at 11:16 AM |
|
|
| Quote: | Originally
posted by 71EJVan
I'm mounting a heater core from a Holden Rodeo truck up under the floor just behind the front beam. I has a bypass vane so the blower behind it will
also push fresh air. Will hook up to the original pipework forward.
Brendan
|
I was thinking of retaining much of the original ductwork and fabbing an airbox toward the front of the center duct for the heater core and fan. This
would be hooked up to the center duct, drawing air from the rear seat "outlets" and pushing it to the front outlets. Recirculating the air is much
more efficient than drawing outside air.
Also, I think that keeping the heater core low will make it easier to get rid of air bubbles.
I'm not sure whether to include it in the Subaru bypass thermostat circuit (as subaru does) or to have a separate bypass to operate the
thermostat.
George
|
|
|
ElusiveStranger
Officially Full-On Dubber
Posts: 330
Threads: 30
Registered: May 28th, 2006
Member Is Offline
Location: Kent. England
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 17th, 2006 at 01:53 PM |
|
|
Hey George, long time no hear!
I'm thinking about recirculating the air in mine (panel van) much Mine will be the way you have described ie suck the cabin air from the back via the
walkthrough 'box'
How's yours coming on?
I'm not too sure how to post images to here but I'll try shortly - give me a coupla weeks.
I'm contemplating the Tom Shields bypass conversion - I've heard a few Aussies are running these too. Comments would be appreciated!
Edit: Changed Commets to comments
[ Edited on 17-12-2006 by ElusiveStranger ]
|
|
|
GeorgeL
Officially Full-On Dubber
Posts: 231
Threads: 11
Registered: February 5th, 2006
Member Is Offline
Location: 7200 miles off the Queensland coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 8th, 2007 at 12:20 PM |
|
|
| Quote: | Originally
posted by ElusiveStranger
Hey George, long time no hear!
I'm thinking about recirculating the air in mine (panel van) much Mine will be the way you have described ie suck the cabin air from the back via the
walkthrough 'box'
How's yours coming on?
I'm not too sure how to post images to here but I'll try shortly - give me a coupla weeks.
I'm contemplating the Tom Shields bypass conversion - I've heard a few Aussies are running these too. Comments would be appreciated!
|
My project has been stalled but will get going again soon. I need to order the intake inverter from COR and start assembling all the other conversion
bits. I'm talking to a dune buggy supplier here about a 2.5 SOHC engine.
George
|
|
|
