| [ Total Views: 931 | Total Replies: 5 | Thread Id: 60494 ] |
|
|
 mwstewart
Learner Dubber
Posts: 2
Threads: 1
Registered: February 15th, 2007
Member Is Offline
Location: UK
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy!
|
| posted on February 15th, 2007 at 07:09 AM |
|
|
02m/Ford bellhousing
Hello guys,
I would like to mate a Ford Focus engine (2.0 Zetec) to an Audi/VW 02M 6 speed gearbox. Adapter plate seems like the easiest option here, so my
question is what's the best way to go about it? I understand the holes and dowels have to be incredibly accurate so what is the safest way to measure
them?
Cheers for any help,
Mark
[ Edited on 15-2-2007 by mwstewart ] |
|
|
sinecure
A.k.a.: Sin
Custom Title Time!
Want another... :(
Posts: 1031
Threads: 76
Registered: March 30th, 2006
Member Is Offline
Location: Lat 27 S, Long 153 E
Theme: UltimaBB Psyche Blue
Mood: Low, slow and SAD to see it go.
|
| posted on February 18th, 2007 at 11:07 PM |
|
|
Ask Seagull (Perth, WA).
A POSSE AD ESSE.
I live in my own little world, but it's okay, they know me here.
|
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 18th, 2007 at 11:46 PM |
|
|
ok
if the holes work out so you can plot them out on a mill with X Y Z your in luck .
if they dont
work off the center of each item
1 ) the motor .
It has a center bearing in the crank , you need a shaft that fits in that , some thing of quality .um lets say a front strut from a car ( good
thinking seagull ) , cut the shaft out & get one end machined so it fits the center bearing .
2) you need the bolts that fit in to the motor housing machined to a point facing out .
3) you need the plate you are going to make the adapter plate out of with a hole the same size ( od ) of the strut ( shaft )
4) slide the plate down the shaft & with a hamer tap around were the points are note they all need to be the same lenth from the back of the motor (
face )
you have now marked the motor side .
gear box is the same , you may need a sleve for the gearbox shaft
or now place it on a face plate in a lathe & clock off the center hole .in doing this machine a step that the plate will sit in the gear box , remove
from the lathe tap in to the gear box bolt the motor up so the gear box is in the correct position & mark the holes with a scribe ( fine point marker
)
remove & drill the holes
fly wheel will do your head in its all measuring
Mark fill in your location so we know were you are
I hope this helps < seagull
Looking for that special lady : PM me for coffee & cake
|
|
|
sinecure
A.k.a.: Sin
Custom Title Time!
Want another... :(
Posts: 1031
Threads: 76
Registered: March 30th, 2006
Member Is Offline
Location: Lat 27 S, Long 153 E
Theme: UltimaBB Psyche Blue
Mood: Low, slow and SAD to see it go.
|
| posted on February 20th, 2007 at 04:13 PM |
|
|
Told ya.
LOL 
A POSSE AD ESSE.
I live in my own little world, but it's okay, they know me here.
|
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 20th, 2007 at 11:33 PM |
|
|
I know I need help dont I !
Looking for that special lady : PM me for coffee & cake
|
|
|
mwstewart
Learner Dubber
Posts: 2
Threads: 1
Registered: February 15th, 2007
Member Is Offline
Location: UK
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy!
|
| posted on February 21st, 2007 at 09:02 AM |
|
|
seagull that's a very nice solution to the problem, cheers! I'm going to have a crack at it this weekend.
:beer |
|
|
