| [ Total Views: 11972 | Total Replies: 35 | Thread Id: 78303 ] |
| Pages: 1 2 |
|
|
 bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on September 22nd, 2009 at 01:24 AM |
|
|
Out of curiosity, i know it doesn't affect me and my setup, but for swing axle, (i would imagine its absolutely same principle as this) but... how do
you go about the wheel bearings being higher than the gearbox itself?
seeing that they are lubed with the transmission oil rather than the separate gease and seal setup like on an IRS?
Is there a sealed bearing conversion or sumfin? I have always wondered thats all... but anywho!
btw though Joel, another good write up mate!
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on September 22nd, 2009 at 08:30 PM |
|
|
most of these people running slammed swingers with 300degrees neg camber will tell you that they oil runs up the tubes every time they go round a
corner
im sceptical but i have heard people talking on thesamba about using sealed bearings
|
|
|
colonel mustard
Son of Jim - Creator of Good
Posts: 2829
Threads: 51
Registered: February 27th, 2009
Member Is Offline
Theme: UltimaBB Pro Black
|
| posted on November 14th, 2009 at 10:38 PM |
|
|
ah. soon! 
|
|
|
57 oval
Seriously Crusin Dubber
Oval type 4 Fuel Injected
Posts: 184
Threads: 48
Registered: February 5th, 2008
Member Is Offline
Location: Whyalla
Theme: UltimaBB Pro Grey
Mood: Oval
|
| posted on November 15th, 2009 at 11:11 AM |
|
|
Excellent write up and the timming is spot on. I just sat my body back on yesterday after doing a full body rebuild and a IRS conversion to the
floorpan, only problem I have is I never had a standard height to start working with and when I put the torsion bars in I have set them way to high. I
will need to take them out and start again.
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on November 15th, 2009 at 11:21 AM |
|
|
wait till you have the engine back in and all the car back together
you will be amazed how much it will settle
mine with a 1 spline drop and no engine sat higher than that
|
|
|
trickysimon
A.k.a.: Simon Azzopardi
Custom Title Time!
100km/h is only 9 seconds away
Posts: 1473
Threads: 43
Registered: December 15th, 2007
Member Is Offline
Location: Wagga Wagga
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 15th, 2009 at 01:12 PM |
|
|
I might need to raise mine. Hit the sidewinder shifting into second 
|
|
|
| Pages: 1 2 |
