| [ Total Views: 2633 | Total Replies: 5 | Thread Id: 83064 ] |
|
|
 vwkj87
Seriously Crusin Dubber
Posts: 103
Threads: 34
Registered: October 21st, 2008
Member Is Offline
Location: Gold Coast, QLD
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 11th, 2010 at 09:30 PM |
|
|
Sandblasting kombi
Does anyone know roughly how much to get a kombi sandblasted? Does anyone prefer any alternatives such as soda blasting or chemical dipping? And does
anyone know or recommend somewhere in Qld Brisbane/Gold Coast area? Any advice would be very helpful.
|
|
|
pod
A.k.a.: paul mrvw061
Compulsive Aussie Vee Dubber
i`ve got to finish this thing one day
Posts: 4980
Threads: 145
Registered: December 28th, 2003
Member Is Offline
Location: campbelltown,nsw
Theme: UltimaBB Pro Yellow
Mood: could be better
|
| posted on April 12th, 2010 at 12:07 AM |
|
|
not an expert here ,but what i`ve read soda blasting is a better alternative to sand blasting ,something to do with warpage of panels ,and on a kombi
you wouldn't want that..
|
|
|
Ragerty
Seriously Crusin Dubber
Posts: 112
Threads: 41
Registered: March 11th, 2006
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 14th, 2010 at 08:12 PM |
|
|
Soda blasting doesn't remove rust but is much kinder to your panels. Sand blast with the right grade grit can work a treat and chemical dip removes
everything and is clean. Sand blast grit gets everywhere. I'd ike to try chemical dip next time..saves a lot of trouble.
|
|
|
vwkj87
Seriously Crusin Dubber
Posts: 103
Threads: 34
Registered: October 21st, 2008
Member Is Offline
Location: Gold Coast, QLD
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 14th, 2010 at 09:02 PM |
|
|
Is soda blasting just for paint then?
|
|
|
 helbus
A.k.a.: Pete S
Super Administrator
Mad fabricator, paint and body
Posts: 7386
Threads: 312
Registered: September 1st, 2002
Member Is Offline
Location: In the garage chopping cars into bits
Theme: UltimaBB Pro Blue
Mood: In the thinking chair
|
| posted on April 15th, 2010 at 12:07 AM |
|
|
Soda or plastic bead blast removes paint, but not rust. It is kind on panels
Garnet (sand) blast removes rust, but will warp flat panels and ruin them
Chemical dipping is the worst, and I have seen more panels thrown away after dipping than sand blasting. At work, any panels an owner brings in that
have been dipped have no guarantee against rust in seams. The acid stays in behind seams and rusts more than ever.
The blaster we use, will use sand on all of the body of a vehicle, except for the flats of panels. That is done with plastic media. It is about $1500
for a sedan and all panels, so a bus would get up around $2000 there. No warpage of panels though. They do everything from Aston Martin DB2, Ferrari
195, Porsche 356 etc.
|
|
|
Dasdubber
A.k.a.: Alan Agyik
23 Windows of Awesome
DAS Resto Haus
Posts: 5746
Threads: 289
Registered: August 26th, 2002
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue
Mood: feeling fine...
|
| posted on April 15th, 2010 at 08:35 PM |
|
|
We have had quite a few cars done by Preptech ( http://www.preptech.com.au ) - a
very nice fellow that only does cars and has done so for many years. He hasn't warped one panel yet (several splitties, bays and a karmann ghia that
we've had done). He doesn't blast the inside of the outer skins, only the framework etc.
He picks up/drops off - gold coast area (not sure about brissy).
Cheers
Al
|
|
|
