| [ Total Views: 634 | Total Replies: 5 | Thread Id: 89813 ] |
|
|
 tayloredvw
Seriously Crusin Dubber
Posts: 165
Threads: 39
Registered: May 17th, 2006
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
Mood: make love not war
|
| posted on April 12th, 2011 at 09:45 PM |
|
|
advice on ratio rockers
Hey guys, I have a 1915 im replacing the heads on. The crank, rods, flywheel have all been balanced when put together but with the standard
un-counterweighted crank.
I have a c-35 cam in it now and the new heads are mofoco 050 with 42inlets and 37 exhausts.
I have either 40 or 48idf carbs to run it. And my question is would 1.4:1 ratio rockers work alright and would 48 idf's be to big?
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on April 12th, 2011 at 10:17 PM |
|
|
The C35 is not for 1.4:1 ratio rockers.
Have a look here
http://www.vwparts.net/mm5/merchant.mvc?Screen=CTGY&Store_Code=VWP&Ca...
I'd only run it with 1.1:1 (stock) rockers, but I'm generally conservative in this area.
As for the 48's, choke them down and they will work ok. Really depends on what you want, rev it's ring off or day to day driveability.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
tayloredvw
Seriously Crusin Dubber
Posts: 165
Threads: 39
Registered: May 17th, 2006
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
Mood: make love not war
|
| posted on April 14th, 2011 at 09:06 AM |
|
|
Thanks matt, do the rockers enhance the lift of the cam?
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on April 14th, 2011 at 11:11 AM |
|
|
Std rockers are 1.1:1 ratio, so by increasing the ratio of the rocker (lever) it increases lift at the valve, but the down side is the acceleration
rate is also increased and this is where problems occur. Performance cams are already designed to reach some max limits and going beyond these usually
causes damage to the valvetrain
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on April 15th, 2011 at 04:08 PM |
|
|
I would run the 40 IDF'S as you have a standard crank, to quote the standard, "Hot to hot rod VW engine's" consenses is that a standard crank is
good for 5000RPM, if you have to rev it to make power you will pound out the centre main bearing over this RPM, i think the C35 that i had earlier in
the piece stops making usable power at about 5500RPM, if you run to larger set of carbs you will not have the bottom end which will make it drivable
for every day use, the book is still in print and is available, old but still revelent
|
|
|
tayloredvw
Seriously Crusin Dubber
Posts: 165
Threads: 39
Registered: May 17th, 2006
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
Mood: make love not war
|
| posted on April 16th, 2011 at 10:40 AM |
|
|
Thanks Matt, you might have just saved me killing my new heads.
|
|
|
