| [ Total Views: 811 | Total Replies: 20 | Thread Id: 90676 ] |
|
|
 wrecker67
A.k.a.: craig
Fahrvergnugen
Posts: 997
Threads: 160
Registered: August 26th, 2002
Member Is Offline
Location: central coast,chain valley bay
Theme: UltimaBB Psyche Green
Mood: fishing,beach,sun,fishing,
|
| posted on May 27th, 2011 at 07:40 PM |
|
|
oil temp sender best place
had a bit of a search on here,where is the best place to get a true reading, in the sump,from the oil pump,to external cooler,or the oil light
swich.
just want to know i am getting a true reading of temp,
cheers
To follow the path: Look to the master, Follow the master, Walk with the master, Become the master
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12764
Threads: 733
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 27th, 2011 at 07:51 PM |
|
|
I reckon tapping into the case beside the strainer or the "rear" cap to the spring plunger thingy
Futue te ipsum!!!
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on May 27th, 2011 at 07:58 PM |
|
|
in my opinion it's good to know the temp of the oil after it has passed through the cooler, this way you can see if the cooler is doing it's job as
the oil is going to the bearing's etc.
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on May 28th, 2011 at 09:16 AM |
|
|
The sump plate itself and the oil pressure switch are the 2 worst areas you can put them.
Dipstick senders work well but for something more permanent Type3 filler area or relief valve plug work well.
I've also seen a few people tap them into the oil filter housing on full flowed setups.
|
|
|
Newt
Wolfsburg Wizard
Posts: 478
Threads: 82
Registered: March 1st, 2008
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Grey
Mood: Born 10 minutes late & never caught up.
|
| posted on May 31st, 2011 at 09:50 PM |
|
|
Joel,
Why is the sump plate a bad spot (other than being exposed to speed humps etc).
Ta
Newt
It is as it is - If you didnt enjoy today, you've missed the opportunity.
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on May 31st, 2011 at 10:44 PM |
|
|
I've found the sump plate to read cold, maybe a dead area of oil circulation as the oil under the strainer sits in a no flow area.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
wrecker67
A.k.a.: craig
Fahrvergnugen
Posts: 997
Threads: 160
Registered: August 26th, 2002
Member Is Offline
Location: central coast,chain valley bay
Theme: UltimaBB Psyche Green
Mood: fishing,beach,sun,fishing,
|
| posted on May 31st, 2011 at 10:58 PM |
|
|
i am thinking of running a external cooler,i have a tap in the sump area,i will try that one,for now it runs from one of them sandwitch plates in
front of the oil filter,
sounds strange but this is a wbx 2.1 engine now air cooled,so i have oil lines from the sandwitch plate to the oil cooler dog house type,some how i
want to add a external cooler,not sure how to run both,need a diagram,would i fit it near the box or run costly oil lines to the front with a cooler
up there,need to drop engine temp a bid,
was told a stand off will help.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
To follow the path: Look to the master, Follow the master, Walk with the master, Become the master
|
|
|
wrecker67
A.k.a.: craig
Fahrvergnugen
Posts: 997
Threads: 160
Registered: August 26th, 2002
Member Is Offline
Location: central coast,chain valley bay
Theme: UltimaBB Psyche Green
Mood: fishing,beach,sun,fishing,
|
| posted on May 31st, 2011 at 11:02 PM |
|
|
you can see the oil lines from the plate the filter is on,would like to relocate the filter plus add a cooler in the system,
i think i can buy a relocate kit ,but then will i lose the original cooler,need a diagram made to see where the lines would run in a circle,
cant be to hard,any ideas,
as you can see the filter is almost touching the pipe.
To follow the path: Look to the master, Follow the master, Walk with the master, Become the master
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on May 31st, 2011 at 11:02 PM |
|
|
I hope you have sealed the tinware and replaced the engine tray seal since that photo above.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
wrecker67
A.k.a.: craig
Fahrvergnugen
Posts: 997
Threads: 160
Registered: August 26th, 2002
Member Is Offline
Location: central coast,chain valley bay
Theme: UltimaBB Psyche Green
Mood: fishing,beach,sun,fishing,
|
| posted on May 31st, 2011 at 11:14 PM |
|
|
old pics,but shows the oil lines etc while the rear is un bolted.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
To follow the path: Look to the master, Follow the master, Walk with the master, Become the master
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on June 1st, 2011 at 09:06 AM |
|
|
I have no oil cooler on the block in my 2054, i have mounted a oil cooler at the front of the car running through a thermostat, there is no pressure
drop and the pressure runs at 60 PSI at 3000 RPM, 20 PSI per 1000 RPM, temp never exced's 190degree's F, i have the temp sender in the return line
to the engine so i can see the oil temp going to the bearing's ect. this lets you see how efective the cooler is in the system.
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on June 1st, 2011 at 09:42 AM |
|
|
| Quote: | Originally
posted by Newt
Joel,
Why is the sump plate a bad spot (other than being exposed to speed humps etc).
Ta
Newt
|
Like Matt said poor circulation and I would imagine road draft having a cooling affect on the sender and plate is the problem too.
I'm guessing that as I originally tried mine there and out on the open road when the engine got it hottest the temp gauge would only read 140f/60c
but if i stopped and just idled around a car park or drivethru it would creep right up which is the time VW oil actually cools down.
I did try a candy thermometer in the dipstick as a comparison a few times and when the gauge said 130f/55c the thermometer said 180f/82c. thats a fair
difference.
Several people have complained of the same problem.
I moved it to the type3 filler area after that, worked much more accurate.
|
|
|
JOE568
Casual Dubber
Posts: 21
Threads: 8
Registered: May 3rd, 2011
Member Is Offline
Location: Gold Coast hinterland,Canungra
Theme: UltimaBB Vintage
|
| posted on June 1st, 2011 at 12:19 PM |
|
|
I run my temp sensor off the sump........seems to work pretty well..as long as you use a good gague....fitting a full flow system,oil cooler and
thermo fan dropped my temp by 30degrees...you can realy give it to it and it wont go over 100degrees with the thermo fan going....if you realy wanted
to find the best place......fit a few sensors in different spots and then find a medium??...would be interesting to see the results.....bla....
|
|
|
wrecker67
A.k.a.: craig
Fahrvergnugen
Posts: 997
Threads: 160
Registered: August 26th, 2002
Member Is Offline
Location: central coast,chain valley bay
Theme: UltimaBB Psyche Green
Mood: fishing,beach,sun,fishing,
|
| posted on June 1st, 2011 at 01:20 PM |
|
|
| Quote: | Originally
posted by vwo60
I have no oil cooler on the block in my 2054, i have mounted a oil cooler at the front of the car running through a thermostat, there is no pressure
drop and the pressure runs at 60 PSI at 3000 RPM, 20 PSI per 1000 RPM, temp never exced's 190degree's F, i have the temp sender in the return line
to the engine so i can see the oil temp going to the bearing's ect. this lets you see how efective the cooler is in the system.
|
what type of lines do you run to the front,and what fittings are you using,lines under the car,
this is what i was thinking just run one up front without the modded dog house type i have..
To follow the path: Look to the master, Follow the master, Walk with the master, Become the master
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on June 1st, 2011 at 03:58 PM |
|
|
That's what i have, i ran 16MM thin wall hydraulic tube thru the car attached to the tunnel, at the front it comes out under the passenger foot rest
and through the front fire wall, at the rear it come out above the torsion bar housing, i silver soldiered male JIC fitting's on each end, both
tube's are bent in one piece and were it exit,s at each end they are protected by large rubber grommet's, all the hose's are stainless steel
braided using speed flow fitting's, use a thermostat, this will keep the temp under control and help the oil to reach it's operating temp sooner,it
is possible to run the oil to cool and will not get hot enough to get rid of the contaminate's.
|
|
|
DubCty
Slammed & Awesome Dubber
Posts: 95
Threads: 11
Registered: June 11th, 2009
Member Is Offline
Location: Launceston, Tas
Theme: UltimaBB Pro Blue ( Default )
Mood: MAD™
|
| posted on June 1st, 2011 at 09:35 PM |
|
|
I ended up tapping the back of my sump this should give me the oil temp at its hottest point, i.e after it has done its job.
Straight Cuts – The Best Preparation For A Wife!
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on June 1st, 2011 at 09:42 PM |
|
|
With the cooler up the front, I think the thermostat is a must, to keep the oil hot, but most importantly to provide a short path for oil to the
bearings on startup. So mount the thermostat as close as possible to the engine.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
wrecker67
A.k.a.: craig
Fahrvergnugen
Posts: 997
Threads: 160
Registered: August 26th, 2002
Member Is Offline
Location: central coast,chain valley bay
Theme: UltimaBB Psyche Green
Mood: fishing,beach,sun,fishing,
|
| posted on June 6th, 2011 at 06:35 PM |
|
|
thanks guys,seems a good topic on testing ,i will see how it goes now i have a good tune,i used a heavier guage wire to the sender,plus moved the wire
away from the extractors,
if i still get a high reading will run a front mount setup,
sounds like a plan.
To follow the path: Look to the master, Follow the master, Walk with the master, Become the master
|
|
|
Newt
Wolfsburg Wizard
Posts: 478
Threads: 82
Registered: March 1st, 2008
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Grey
Mood: Born 10 minutes late & never caught up.
|
| posted on June 7th, 2011 at 09:54 PM |
|
|
Dubcty
Did you just drill and tap?
Was there enough case for that?
Cheers
Newt
It is as it is - If you didnt enjoy today, you've missed the opportunity.
|
|
|
dangerous
A.k.a.: Dave Butler Muffin Man
23 Windows of Awesome
Posts: 5901
Threads: 178
Registered: January 6th, 2005
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
Mood: 591
|
| posted on June 8th, 2011 at 05:17 AM |
|
|
http://bobhooversblog.blogspot.com/2006/11/vw-normal-oil-temp.html
This is some good info,
but remember he is talking degrees F not C , so do some converting.
| Quote: | Originally
posted by westi
That's mad Alan.
|
|
|
|
Newt
Wolfsburg Wizard
Posts: 478
Threads: 82
Registered: March 1st, 2008
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Grey
Mood: Born 10 minutes late & never caught up.
|
| posted on June 8th, 2011 at 11:14 PM |
|
|
Hmm, its a thought....
Oil temp was picked-off at the inlet to the oil pump, a suitable adaptor replacing the threaded plug found there. (Ed. Note: Only found on early
crankcases.)
It is as it is - If you didnt enjoy today, you've missed the opportunity.
|
|
|
