| [ Total Views: 930 | Total Replies: 6 | Thread Id: 90858 ] |
|
|
 jeremyluke
Seriously Crusin Dubber
Posts: 126
Threads: 16
Registered: March 11th, 2010
Member Is Offline
Location: Wollongong NSW
Theme: UltimaBB Pro Navy
|
 posted on June 5th, 2011 at 05:35 PM |
|
|
Want to change to Electronic Ignition. Help ??
I am going to remove the points from the project that I am working on. Im keeping the car close to stock, but want to remove the points. Looking at
buying something from Cip1.
What are my options as I really dont know anything about the various kits or new distributors available.
Like i said, the car will remain almost stock, so there wont be any upgrades to the engine apart from ignition system.
Any advice or help would be appreciated
Thanks
Jeremy
ps Its a '71 super
|
|
|
jeremyluke
Seriously Crusin Dubber
Posts: 126
Threads: 16
Registered: March 11th, 2010
Member Is Offline
Location: Wollongong NSW
Theme: UltimaBB Pro Navy
|
| posted on June 6th, 2011 at 05:46 PM |
|
|
??
bump
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 6th, 2011 at 06:00 PM |
|
|
Ok - hope this helps
1 Pertronic or Compufire - cheap ($100??) and fits exist dizzy. OK-isk
2 Scorcher - This is what I have. New dizzy, not reused 009 - but still has a rotor. All Bosh parts, readily available. Been VERY happy. $400ish
3 Dis-X $600ish individual coil pack. No rotors. Good but have "HEARD" of some unknown failure. Not proved in my books and I will probably go this
way when I have some money to waste
4 MSD - lots of money and options. For the serious
Futue te ipsum!!!
|
|
|
jeremyluke
Seriously Crusin Dubber
Posts: 126
Threads: 16
Registered: March 11th, 2010
Member Is Offline
Location: Wollongong NSW
Theme: UltimaBB Pro Navy
|
| posted on June 6th, 2011 at 06:53 PM |
|
|
What about buying a PERTRONIX VACUUM ADVANCE (SVDA) DISTRIBUTOR with the electric ignition already installed ?
The car currently has a mechanical advance distributor, so is it worth paying a bit more for the vacuum ?
The Pertronix vacuum advance (with ignition module installed)
and a Flame thrower coil
Will cost $250 AUD including postage, but if i do decide on getting anything i might wait till Cip1 puts there deals up again, just missed out on the
15%off one
|
|
|
shokwave2
A.k.a.: Matt Hamilton
Officially Full-On Dubber
Posts: 289
Threads: 28
Registered: March 7th, 2010
Member Is Offline
Theme: UltimaBB Psyche Blue
|
| posted on June 6th, 2011 at 08:43 PM |
|
|
How about you try Rod Penrose. He's local and he may have what you're looking for if you tell him what you're after. It may be cheaper as well.
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
 posted on June 6th, 2011 at 11:19 PM |
|
|
Hi
check out aircooled.net for SVDA Distributors...
with Pertronix fitted...
Lee
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
jeremyluke
Seriously Crusin Dubber
Posts: 126
Threads: 16
Registered: March 11th, 2010
Member Is Offline
Location: Wollongong NSW
Theme: UltimaBB Pro Navy
|
| posted on June 7th, 2011 at 05:35 PM |
|
|
Hey Lee
Read your email and check out the Distributors, but which of them are you refering to ? Then ACN SVDA or the Pertronix SVDA? Also will i need to
upgrade the Coil if i purchase one of these ?
Jeremy
|
|
|
