| [ Total Views: 740 | Total Replies: 5 | Thread Id: 92757 ] |
|
|
 bugzla
Custom Title Time!
Posts: 1164
Threads: 240
Registered: June 9th, 2007
Member Is Offline
Location: townsville
Theme: UltimaBB Pro Blue ( Default )
Mood: always happy
|
| posted on September 20th, 2011 at 09:03 PM |
|
|
crank shaft end float
hey guys got a bit of a problem messured my end float for my engine so i can get the flywheel on but have found i have .50 mm worth of end float with
no shims it seems the only shims i have are .24, .26, .30 way to big as it sits tight,a sollution to my problem or what shims are needed or should i
say available so i can get it to the required amount
cheers
stevo
|
|
|
ragged
A.k.a.: David
Wolfsburg Wizard
Just ask if you need HELP!
Posts: 478
Threads: 46
Registered: January 25th, 2005
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue
Mood: Medication seems to be working
|
| posted on September 21st, 2011 at 02:23 PM |
|
|
What engine are you working on? Does the flywheel have an 'O' ring?
Cheers dave
|
|
|
bugzla
Custom Title Time!
Posts: 1164
Threads: 240
Registered: June 9th, 2007
Member Is Offline
Location: townsville
Theme: UltimaBB Pro Blue ( Default )
Mood: always happy
|
| posted on September 21st, 2011 at 03:10 PM |
|
|
yes there is an o ring its a 69mm crank std in 1835cc was thinkng of putting a metal gaskit btween the flywheel and crank
|
|
|
bugzla
Custom Title Time!
Posts: 1164
Threads: 240
Registered: June 9th, 2007
Member Is Offline
Location: townsville
Theme: UltimaBB Pro Blue ( Default )
Mood: always happy
|
| posted on September 21st, 2011 at 10:43 PM |
|
|
been told to machine the flywheel mateing surface to the crank so it will be going to the machine shop tomorrow
|
|
|
dangerous
A.k.a.: Dave Butler Muffin Man
23 Windows of Awesome
Posts: 5901
Threads: 178
Registered: January 6th, 2005
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
Mood: 591
|
| posted on September 22nd, 2011 at 05:30 AM |
|
|
If you need more room for the shims,
the area that the shims ride on is where it needs to be machined, not the crank mounting face.
Please make sure that your measurment is accurate though.
Some times you can get a false reading if the cylinders and pistons are fitted.
Try one of your shims, and see if the end float IS reduced by that same amount.
This will enable you to calculate the amount of machining required,
or determine if something else is going on.
It is quite rare to not be able to fit at least two shims in there ,
but even then it is because something is not quite original VW.
| Quote: | Originally
posted by westi
That's mad Alan.
|
|
|
|
bugzla
Custom Title Time!
Posts: 1164
Threads: 240
Registered: June 9th, 2007
Member Is Offline
Location: townsville
Theme: UltimaBB Pro Blue ( Default )
Mood: always happy
|
| posted on September 22nd, 2011 at 07:25 PM |
|
|
thanks dave
ive messured twice so it sould be all go
|
|
|
