| [ Total Views: 1137 | Total Replies: 5 | Thread Id: 101067 ] |
|
|
 vassy66T1
A.k.a.: Marcus Vass
Veteran Volks Folk
Wow ... are U reading this?
Posts: 2120
Threads: 76
Registered: June 4th, 2003
Member Is Offline
Location: Brisvegas
Theme: UltimaBB Streamlined2
Mood: Happy to own a VW
|
| posted on March 3rd, 2013 at 11:25 AM |
|
|
Mounting of seat
Hey there
I am mounting the seat in my beetle and cannot seem to find any info from Sparco with requirements for mounting the seat. It is a Sparco Pro 2000
I known that you can buy the seat mount to use for the side mount, (not my preference) but in my setup I would prefer to use the 4 captive nuts under
the seat.
Can I just use the 4 mounting bolts under the seat?
Is this adequate for CAMS and the seat?
Pics below show that I am using rollcage tube and I will drill and bush the tube for the bolts to fix the seat.
Appreciate your information since CAMS and Sparco seem to be light on.
My seat mounting tubes
Captive nuts in side of seat
Captive nuts in base of seat. This is what I would like to use (4 of)
FIA approved side seat mounts (yes I know they are there but don't want to use them unless I absolutely must  )
|
|
|
BiX
Veteran Volks Folk
Posts: 2499
Threads: 154
Registered: September 2nd, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 4th, 2013 at 08:42 AM |
|
|
I don't see why the bottom mounts aren't allowed. They should be built as per the side mounts. Maybe email Sparco and confirm from them?
I have no sympathy for my car, only the wallet that pays for it!
Go hard or go home!!!!
|
|
|
vassy66T1
A.k.a.: Marcus Vass
Veteran Volks Folk
Wow ... are U reading this?
Posts: 2120
Threads: 76
Registered: June 4th, 2003
Member Is Offline
Location: Brisvegas
Theme: UltimaBB Streamlined2
Mood: Happy to own a VW
|
| posted on March 4th, 2013 at 10:20 AM |
|
|
I did find some info this morning that finally confirmed I could use either bottom or side mount as far as Sparco were concerned.
|
|
|
bigrudi
Wolfsburg Wizard
Posts: 401
Threads: 118
Registered: April 12th, 2005
Member Is Offline
Location: Sydney, Australia
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 4th, 2013 at 03:34 PM |
|
|
Side mounts give u a lot more adjustability as in seat height and angle compared to fixed on the botom plus if mounted on the sparco brkts u ca mount
the seat closer to the centre of the car giving more seat to side bar clearance,the correct angle in a race seat is very important as there is no give
in them at all to much angle back difficult to press pedals and eccess pressure under legs too far forward lower back probs got to fit it so your
comfortable my5cents cheers Rudi
|
|
|
vassy66T1
A.k.a.: Marcus Vass
Veteran Volks Folk
Wow ... are U reading this?
Posts: 2120
Threads: 76
Registered: June 4th, 2003
Member Is Offline
Location: Brisvegas
Theme: UltimaBB Streamlined2
Mood: Happy to own a VW
|
| posted on March 4th, 2013 at 05:01 PM |
|
|
Thanks Rudi
Much appreciated 
|
|
|
lou0060
Wolfsburg Wizard
Posts: 568
Threads: 30
Registered: December 12th, 2010
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 4th, 2013 at 08:31 PM |
|
|
ahhh, progress!
1971 karmann ghia Cabrio - Cruising 
1963 beetle Sunroof - gathering dust 
1968 race beetle - twin turbo Subaru - stress relief 
1960 beetle - old school low & slow  |
|
|
