| [ Total Views: 710 | Total Replies: 4 | Thread Id: 104576 ] |
|
|
 jobie
Slammed & Awesome Dubber
Posts: 77
Threads: 26
Registered: May 17th, 2011
Member Is Offline
Theme: XMBX Pro Green
|
| posted on January 3rd, 2014 at 06:47 PM |
|
|
Dropping a Bug
Hi Dubbers,
Two Questions if I may:
I have just purchased a 56 bug and plan to drop and narrow the front to fit 17" BRMs to look similar to this ( http://forums.aussieveedubbers.com/viewtopic.php?tid=85675&page=7 ). I would also like to fit disc brakes.
1. Can anyone give me any advice on other suitable combinations to achieve the above. I assume 2.5 inch drop and 2 inch narrowed beam??? I wish money
was no object but it will be!
I was not planning on doing this straight away but I need to move it and the brakes are shot (apparently they Have been for a couple of years). I
tried bleeding them and fluid just ran out of the front drums. I don't want to spend money on brakes that are to be replaced in the next little while
but think I might need to?
2. Do I need to replace just my brake seals or the cylinders (I assume they come with the seals) and if so where do I get them I'm in Melbourne's
Eastern burbs?
Cheers,
Joel
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on January 3rd, 2014 at 08:48 PM |
|
|
Are those 17" BRMs 205 PCD or 112 PCD? That will make a big difference with brake disc kit options and price.
There are more 112 brake options than 205 and they are cheaper too.
to get her rolling the wheel cylinders aren't too expensive. Vollks is probably the cheapest and can be bought online. Then VVDS in Sydney and Mick
Motors in Brisbane.
madness is in the eye of the beholder  |
|
|
jobie
Slammed & Awesome Dubber
Posts: 77
Threads: 26
Registered: May 17th, 2011
Member Is Offline
Theme: XMBX Pro Green
|
| posted on February 10th, 2014 at 12:50 PM |
|
|
Thank psimitar,
I want to retain the origonal 205 PCD and they are 17" BRM's.
I have but in new cylinders and they have made bugger all difference car only moderatly slows! I have discovered that the rear brakes are non existant
as well.
I am going to put a new disc kit on it (as well as redo the rear) and am considering theses - http://vwparts.aircooled.net/Wide-5-Disc-Brake-Kit-Link-Pin-2-1-2-Lowered-p/w... - Has anyone had any experience with them? I
have also seen the Jamar brakes advertised OS. Has anyone had any experience with these?
With each of the above does anyone know of an Australian distributor?
Cheers All,
Joel
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on February 10th, 2014 at 03:24 PM |
|
|
Just keep in mind any brake and suspension modifications will have to be engineer approved.
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on February 10th, 2014 at 07:30 PM |
|
|
First of all I'd get the orig brakes working properly. When working properly hydraulically and the shoes adjusted correctly then the drums will pull
the car up quite nicely. Only if you have a really HiPo engine would I bother with discs.
And as VW060 says, you need to get an engineers approval and it's best to do that before you fork out the cash on whatever you choose cos many
engineers don't like the use of adapter plates to allow the wide 5 wheels to fit. They are quite retarded in this respect so you have to find one
with a brain 
madness is in the eye of the beholder |
|
|
