| [ Total Views: 942 | Total Replies: 5 | Thread Id: 104839 ] |
|
|
 zeppelin-vwwe
Commited Dubber
Posts: 61
Threads: 13
Registered: February 13th, 2011
Member Is Offline
Location: Menai nsw
Theme: UltimaBB Pro Blue ( Default )
|
 posted on January 24th, 2014 at 01:44 PM |
|
|
Changing carbys
Hey guys.
Just wanted to ask some advice about changing carbys.
I've got a '62 bug running what I believe is a 1641cc motor (it may be higher, I don't know. It's never been pulled apart to be sure)
Anyway it has twin kadrons which I want to get rid of. Never been happy with them. Sick of them always going out of tune.
Want to go a single central mount carby.
I've got my hands on a new '44 IDA Webber, however the mechanic I might get to install it says I'm better off going original, with a '34pct vw
carb.
Just want to get your thoughts???
Is anyone out there running a 1641cc with a 44??
If so how do you find it? It's a very strong little motor so i don't want to sacrifice power by going original.
I don't have much money to spent so dont want to waste money changing carbs, then having to change again.
I'd greatly appreciate any feedback.
thanks dubbers
|
|
|
Klaus
Custom Title Time!
Posts: 1439
Threads: 100
Registered: August 25th, 2004
Member Is Offline
Location: Wollongong
Theme: UltimaBB Pro Blue ( Default )
Mood: Heavily modified
|
| posted on January 24th, 2014 at 02:44 PM |
|
|
Kadrons on that size motor generally run quite nice , but depends the condition of carbs .
When was the last time you pulled them apart to check throttle plates or gaskets might be time for a new linkage . Centre mount would be a backward
step performance wise .
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12757
Threads: 732
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 24th, 2014 at 02:57 PM |
|
|
It won't be an IDA - it will be an IDF if its a 44
If its an IDA 48 I doubt you will get a manifold
Most people I know with single non progressive centre mounted carbs have never jetted them properly.
If you do go that way make sure you have manifold heat to give yourself half a chance of getting it to work
Futue te ipsum!!!
|
|
|
zeppelin-vwwe
Commited Dubber
Posts: 61
Threads: 13
Registered: February 13th, 2011
Member Is Offline
Location: Menai nsw
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 26th, 2014 at 03:09 PM |
|
|
AH yeh thanks guys
yeh it is an IDF. I mis typed.
When i bought it three years ago, it was running twin del'orto 48's!! On a 1641cc. Rediculous!! The kadrons of course were better. But i've since
realised there are bigger issues at steak here, there is fuel getting into the oil sump. not sure what's wrong here, The right side has always been a
bit doggish, the overjetted dels f#
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on January 26th, 2014 at 07:00 PM |
|
|
A single 44 presents a few different problems to duals, the smallest chocks are 28mm and would probably work on a 1641, there are quite a few articles
on the net , http://www.aircooled.net/vw-carburetors-jetting-102/
|
|
|
ragged
A.k.a.: David
Wolfsburg Wizard
Just ask if you need HELP!
Posts: 478
Threads: 46
Registered: January 25th, 2005
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue
Mood: Medication seems to be working
|
| posted on January 26th, 2014 at 10:22 PM |
|
|
Were the Kadrons new or secondhand when fitted? What ever carby you decide to run will need proper setting up depending on the engine capacity,
the camshaft and your compression ratio. Then it also matters what ignition/distributor you are using, and that is working correctly too.
Do you park your car on a slope? with the front of the car highest? Dave
|
|
|
