| [ Total Views: 883 | Total Replies: 11 | Thread Id: 105097 ] |
|
|
 baja burley
Officially Full-On Dubber
Posts: 325
Threads: 54
Registered: September 11th, 2008
Member Is Offline
Location: ipswich, QLD
Theme: UltimaBB Psyche Grey
|
| posted on February 16th, 2014 at 04:18 PM |
|
|
Weber IDF troubles
Hi lads, I've just pulled my bug out of the shed again after about 5 years of neglect
Went and did a quick tune on the carbs ( twin 40IDF) and just cannot get the thing to run nicely, 1600dp btw. It's running 50 idles, so jetting is
not an issue.
I did notice a dribble from the accel pump jet? The little grey one that pokes out the side of the barrel. It's the one that squirts when you pump
throttle, just not sure what the 'jet' is called..
Is this a problem seen much before? What needs fixing?
This thing uses a ridiculous amount if fuel too.
Cheers
Luke
There are three types of people in this world - people who can count and people who can't....
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12757
Threads: 732
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 16th, 2014 at 04:37 PM |
|
|
Probably gunk caught under the needle and seat
Futue te ipsum!!!
|
|
|
baja burley
Officially Full-On Dubber
Posts: 325
Threads: 54
Registered: September 11th, 2008
Member Is Offline
Location: ipswich, QLD
Theme: UltimaBB Psyche Grey
|
| posted on February 16th, 2014 at 05:07 PM |
|
|
Is it easy to get in there and clean it out?
There are three types of people in this world - people who can count and people who can't....
|
|
|
ian.mezz
Wolfsburg Elder
I never said, I could write or spell
Posts: 3913
Threads: 280
Registered: September 11th, 2004
Member Is Offline
Location: Newcastle
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy
|
| posted on February 16th, 2014 at 05:23 PM |
|
|
youtube is your friend
.
http://www.youtube.com/watch?v=rl1Nkuk99Pc
|
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 18th, 2014 at 12:50 AM |
|
|
Hi mate, I believe I sold you these carbs years ago... My name on here at the time would have been bajamick or 1916baja... I did tell you they needed
an air leak fixed on the butterfly shafts. If you have not had this fixed they won't run properly. Then they'll need to be jetted to suit your
motor. They were jetted to suit my 1916cc.
Hope this helps.
Mick.
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
mnsKmobi
Wolfsburg Wizard
Posts: 589
Threads: 27
Registered: August 27th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 18th, 2014 at 08:42 PM |
|
|
| Quote: | Originally
posted by baja burley
Hi lads, I've just pulled my bug out of the shed again after about 5 years of neglect
Went and did a quick tune on the carbs ( twin 40IDF) and just cannot get the thing to run nicely, 1600dp btw. It's running 50 idles, so jetting is
not an issue.
I did notice a dribble from the accel pump jet? The little grey one that pokes out the side of the barrel. It's the one that squirts when you pump
throttle, just not sure what the 'jet' is called..
Is this a problem seen much before? What needs fixing?
This thing uses a ridiculous amount if fuel too.
Cheers
Luke
|
What is the fuel pressure? Could be too high.
|
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
| posted on February 18th, 2014 at 10:30 PM |
|
|
If they have been sitting for 5 years then you really should pull them down for a freshen up. Old fuel can leave a varnish like residue in carbs that
can easily block passages and cause you grief.
Oxidisation of the housings etc can also cause problems with blockages, and O rings will deteriorate.
Its worth taking the hour or so to do a pull down and clean 
|
|
|
baja burley
Officially Full-On Dubber
Posts: 325
Threads: 54
Registered: September 11th, 2008
Member Is Offline
Location: ipswich, QLD
Theme: UltimaBB Psyche Grey
|
| posted on February 20th, 2014 at 09:41 PM |
|
|
Really Mick? I vaguely remember the 1916 chat! Far out that was a long time ago. It seems I should pull them down and rebuild anyway. I cant remember
any chat about air leaks, was too long ago. When you say it was in the shaft, do you remember if it was a damaged butterfly or something else?
There are three types of people in this world - people who can count and people who can't....
|
|
|
baja burley
Officially Full-On Dubber
Posts: 325
Threads: 54
Registered: September 11th, 2008
Member Is Offline
Location: ipswich, QLD
Theme: UltimaBB Psyche Grey
|
| posted on February 20th, 2014 at 09:46 PM |
|
|
I did check the idle jets - 50 jets. Surely the others can wait until its idling and running sweet to be swapped and dialed in yeah?
There are three types of people in this world - people who can count and people who can't....
|
|
|
baja burley
Officially Full-On Dubber
Posts: 325
Threads: 54
Registered: September 11th, 2008
Member Is Offline
Location: ipswich, QLD
Theme: UltimaBB Psyche Grey
|
| posted on February 20th, 2014 at 09:49 PM |
|
|
Fuel pressure is whatever is coming from the factory pump
There are three types of people in this world - people who can count and people who can't....
|
|
|
mnsKmobi
Wolfsburg Wizard
Posts: 589
Threads: 27
Registered: August 27th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 21st, 2014 at 12:28 PM |
|
|
| Quote: | Originally
posted by baja burley
Fuel pressure is whatever is coming from the factory pump
|
Apparently factory pumps can put out higher pressure than the webers can cope with. I changed to a Carter rotary because my stock pump stopped putting
out anything!
Here is a thread on The Samba which has lots of useful stuff about putting dual carbs on a T1 engine, including about fuel pressure:
http://www.thesamba.com/vw/forum/viewtopic.php?t=572107&postdays=0&postorder=asc&start=0
|
|
|
Performance Upholstery
Officially Full-On Dubber
Posts: 229
Threads: 10
Registered: November 13th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on February 25th, 2014 at 05:55 PM |
|
|
The air leak was behind the linkage on the left hand carbie I believe... Between the carb body and the butterfly shaft. ( the shaft the butterflies
are bolted to) I did explain this, that's why they were so cheap! It's why I could never get them to run right .. Always had an erratic idle. I
went to kadrons and sold the whole kit with linkage and manifolds for like $200... Spray some wd40 or something like that on the 2 throttle linkages
when it's running like crap and watch the revs change. They need rebuilding including that seal.
Performance Upholstery
Cars, boat seats, furniture and more!
0439002870
performanceupholstery@live.com.au
Mt Gravatt east Qld.
|
|
|
