| [ Total Views: 1239 | Total Replies: 5 | Thread Id: 105476 ] |
|
|
 RENNWAGEN
A.k.a.: shane
Seriously Crusin Dubber
Posts: 158
Threads: 43
Registered: September 9th, 2003
Member Is Offline
Location: Sydney's Nthn Beaches
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 19th, 2014 at 07:17 PM |
|
|
Broken starter ring gear
I have an ej20t in a split with an Lbug ssp gearbox. I ran the car for a few years but took it of the road I while back. Last time I tried to start it
I found that the starter ring gear was slipping on the fly wheel however I have now pulled the engine and the ring gear is actually cracked. I have to
move the car and need it to run. I was hoping that I could just put a couple of dowels in to stop the gear slipping so that I could start it but if
I do that now I will have a long gap where the crack is and I'm guessing that the starter will get hung up on this? I only need to start it a couple
of times and once I've finished the body work I'm planning on a subigears box so I'd really prefer not to have to by another flywheel to only use
it a couple of times. Does anyone have any thoughts? It hasn't been run in a couple of years so I don't want to have to count on clutch starting it
because if it doesn't start straight off I will be well and truly buggered.
|
|
|
vlad01
Compulsive Aussie Vee Dubber
Posts: 4270
Threads: 109
Registered: June 3rd, 2010
Member Is Offline
Location: Kyneton, VIC
Theme: UltimaBB Pro Blue ( Default )
Mood: Side ways
|
| posted on March 19th, 2014 at 08:58 PM |
|
|
the ring gear is heated and shrunk on.
You will need to take it to a shop that can do ring gear replacement.
71 notchback,
Past owner of, 70 NB, 73 SB and 72 FB TLE |
|
|
RENNWAGEN
A.k.a.: shane
Seriously Crusin Dubber
Posts: 158
Threads: 43
Registered: September 9th, 2003
Member Is Offline
Location: Sydney's Nthn Beaches
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 20th, 2014 at 11:43 AM |
|
|
Yeah I know I should get it fixed properly but didn't really want to spend the money on something I'm only going to use a couple of times. I was
hoping to bodgy it up to get it moved and then I plan to replace the gearbox so the flywheel will no longer be needed.
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on March 20th, 2014 at 07:50 PM |
|
|
What about removing the ring gear, welding it up, then refit it by the usual heat/shrink fit.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
RENNWAGEN
A.k.a.: shane
Seriously Crusin Dubber
Posts: 158
Threads: 43
Registered: September 9th, 2003
Member Is Offline
Location: Sydney's Nthn Beaches
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 20th, 2014 at 07:53 PM |
|
|
That is looking like number one option at the moment.
|
|
|
mackaymanx
A.k.a.: Brent
Custom Title Time!
Posts: 1611
Threads: 97
Registered: January 12th, 2006
Member Is Offline
Location: Mackay.QLD
Theme: UltimaBB Pro Blue
Mood: Brad'ed Off 
|
| posted on March 20th, 2014 at 08:41 PM |
|
|
So you are using an adapter plate and flywheel? You don't need to buy a new flywheel, you just need a new ring gear. From what I've seen the
conversion flywheels use the ring gear from the 2 litre type IV flywheel, you should be able to find one in Sydney.
Quote of the week
"Do I wish to send them to you again, nope, no interest can't be bothered really, to much hassle for little or no return."
 |
|
|
