| [ Total Views: 772 | Total Replies: 5 | Thread Id: 106209 ] |
|
|
 GottaSplit
A.k.a.: Jamie
Seriously Crusin Dubber
Posts: 101
Threads: 8
Registered: November 20th, 2010
Member Is Offline
Location: Northern Beaches Sydney
Theme: UltimaBB Psyche Blue
|
| posted on May 31st, 2014 at 09:12 PM |
|
|
AA Piston kits
Hey guys...
As per the title, have any of you guys bought/installed these kits? I have looked at their website a few months ago, just weighing up my options.
As I am close to getting my Beetle on the road. Its a stock stale air 40hp, was looking at their big bore 40 horse kit just to freshen it up and give
it a little more oomph....
Maybe even buy the 1916 kit as well for my bus.
cheers Jamie
1960 11 Window
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 31st, 2014 at 09:55 PM |
|
|
I have heard good and bad about them
Mahle, JE or Wiseco would be better
Anything forged rather than cast - which i am pretty sure is what AA is
For under a 6,000 rev mid power motor I reckon they would be fine
Doubt I would use them in an 8,000 rev 150HP stonker
Futue te ipsum!!!
|
|
|
fish26
A.k.a.: benito
Fahrvergnugen
Posts: 903
Threads: 38
Registered: July 13th, 2007
Member Is Offline
Location: sydney
Theme: UltimaBB Pro Grey
Mood: Ken awesome
|
| posted on June 1st, 2014 at 12:23 AM |
|
|
AA 40hp kit consists of cast iron cylinders and Hypereutectic pistons which will be fine for your and most applications.
Since hypereutectic pistons are stronger than the old fashioned cast in steel supported skirt cast pistons the rules have changed and unless you need
the extra strength of forged it is unlikely you need anything more. The other consideration is forged pistons need more clearance of a eutectic piston
and usually wear the rings faster due to piston rock.
bitten by the bug..........several times
|
|
|
Stanley
Compulsive Aussie Vee Dubber
I guess the reward is in the doing of it
Posts: 4523
Threads: 270
Registered: March 13th, 2003
Member Is Offline
Location: Karalee...near Ipswich Qld
Theme: UltimaBB Psyche Grey
Mood: caught a bolt of lightning cursed the day I let it go
|
| posted on June 1st, 2014 at 10:18 AM |
|
|
Ran AA 87mm kit in my notch for a few years...still going strong as far as i know.
|
|
|
FROSTY
Insano Dub Head
Posts: 744
Threads: 65
Registered: May 11th, 2009
Member Is Offline
Location: Palm Beach Qld
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 1st, 2014 at 05:29 PM |
|
|
I'm currently running (flogging the shit out of) AA 1776 piston and cylinder kit (69mm stroke) in my drag car, i have had them to 8000rpm and no
problems (yet) i have run8.04 on the 1/8th and 12.75 1/4. I would have no hesitation using them in a road car. (this is my opinion)
thanks
Jason
|
|
|
bajachris88
A.k.a.: Chris Leete
23 Windows of Awesome
The international telephone dialing code for Antarctica is 672.
Posts: 6661
Threads: 534
Registered: April 8th, 2005
Member Is Offline
Location: Tanah Merah, SE-QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: A bee bit ma' bottom, now ma' bottom's big!
|
| posted on June 1st, 2014 at 07:27 PM |
|
|
I have AA 94mm piston kit. Crankshaft engineering didn't have any complaints or issues balancing em'.
After a long background check on Samba, the racer boys were keen on em' as the pistons are lighter than other competitors products, reducing the
reciprocating mass  .
(ô_!_/ô) (ô_!_/ô)
69' baja: kombi box, thing spindles, irs, disc front, type 3 rear drums, 2 inch lift kit, 31x10 rears. 
New engine in process: 94mm p&bs, 74mm C/w chomol Crank, 35.5x39 SP heads, turbo. Wierd combo, hopeful torque monsta! |
|
|
