| [ Total Views: 915 | Total Replies: 16 | Thread Id: 106236 ] |
|
|
 jackthepom
Casual Dubber
Posts: 20
Threads: 6
Registered: November 19th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 3rd, 2014 at 10:59 AM |
|
|
Crooked motor - beetle with 67 gearbox - Crooked Motor
Hey guys
I recently put a 67 beetle gearbox in my 61 then fitted a 1600 twinport motor.
Since doing so the motor sits crooked in the engine bay, the tinware has about 2-3mm clearence from the body on the driver side. But the passenger
side has about 10-12mm clearence.
I have been told to change the nose cone on the gearbox but dont knkw the definite solution!!
Please help!
|
|
|
vduboy
Insano Dub Head
Posts: 702
Threads: 41
Registered: October 6th, 2012
Member Is Offline
Theme: UltimaBB Streamlined2
Mood: Dying to get more buggy building time..
|
| posted on June 3rd, 2014 at 12:06 PM |
|
|
Check your gear box mounts make sure they aren't torn/damaged, Got any pics?
It will all be OK in the end, if it's not OK it's not the end!
|
|
|
jackthepom
Casual Dubber
Posts: 20
Threads: 6
Registered: November 19th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 3rd, 2014 at 01:34 PM |
|
|
Box has been reconditioned
all mounts are new etc
|
|
|
Camo
A.k.a.: Kev
Custom Title Time!
Posts: 1936
Threads: 209
Registered: October 29th, 2007
Member Is Offline
Location: Sydney - Liverpool area
Theme: UltimaBB Pro Blue
|
| posted on June 3rd, 2014 at 04:23 PM |
|
|
Frame horns could be bent or the rear of the body.
Kev
|
|
|
Stanley
Compulsive Aussie Vee Dubber
I guess the reward is in the doing of it
Posts: 4523
Threads: 270
Registered: March 13th, 2003
Member Is Offline
Location: Karalee...near Ipswich Qld
Theme: UltimaBB Psyche Grey
Mood: caught a bolt of lightning cursed the day I let it go
|
| posted on June 3rd, 2014 at 08:57 PM |
|
|
There is a bit of clearance in the mounting holes usually from wear. I'd say if you loosen everything off you'll be able to realign it.
|
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on June 4th, 2014 at 06:18 AM |
|
|
Check the gearbox is on centre, did the original engine sit in the centre of the engine bay, some times you have to loosen all the body bolts and move
the entire body over if everything else checks out ok.
|
|
|
jackthepom
Casual Dubber
Posts: 20
Threads: 6
Registered: November 19th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 4th, 2014 at 10:28 AM |
|
|
Everything was okay until I replaced engine and gearbox
|
|
|
REDKG
Officially Full-On Dubber
Posts: 327
Threads: 76
Registered: August 29th, 2002
Member Is Offline
Location: sutherland-sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 4th, 2014 at 07:34 PM |
|
|
as they said, loosen ALL gearbox mount bolts and maybe the mount frame across the horns..You may need to use a jack and bars to move the engine.
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on June 4th, 2014 at 09:02 PM |
|
|
Was it a split case non synchro first gearbox originally?
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
Governor
Wolfsburg Wizard
Posts: 414
Threads: 23
Registered: November 22nd, 2008
Member Is Offline
Location: in your mind
Theme: UltimaBB Pro Blue ( Default )
Mood: yes please
|
| posted on June 4th, 2014 at 10:25 PM |
|
|
Silly question but did you grind the box out for the flywheel?
|
|
|
jackthepom
Casual Dubber
Posts: 20
Threads: 6
Registered: November 19th, 2013
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 4th, 2014 at 10:40 PM |
|
|
No I didn't
I bought the box from a guy who had it running in a 67 with a 1600 twin port
|
|
|
Governor
Wolfsburg Wizard
Posts: 414
Threads: 23
Registered: November 22nd, 2008
Member Is Offline
Location: in your mind
Theme: UltimaBB Pro Blue ( Default )
Mood: yes please
|
| posted on June 4th, 2014 at 11:01 PM |
|
|
I only ask because if the flywheel isnt sitting in the box correctly the engine might not be mated to the box?
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on June 5th, 2014 at 09:49 AM |
|
|
Was it a non synchro box that you swapped out?
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on June 6th, 2014 at 07:56 PM |
|
|
Get the rear up on axles stands and lay under the gearbox so you can see if the gearbox sits parallel with the framehorns and if the engine has
properly mated to the gearbox.
This will let you know where the issue lies as could be gearbox mounts or could be the engine not seated properly.
Easiest way to find out really 
madness is in the eye of the beholder  |
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on June 6th, 2014 at 08:40 PM |
|
|
He's been told to change the nose cone, my guess it's a '60 or earlier chassis with a crash box. The mounts and horns vary and adapting the later
box isn't always easy.
Have a look where the gear selector goes into the hole in the pan. It should line up in the middle of the hole and another area to check is that the
axle tubes have plenty of clearance for the boots. It's a good indication that everything is in place.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on June 6th, 2014 at 09:55 PM |
|
|
| Quote: | Originally
posted by matberry
He's been told to change the nose cone, my guess it's a '60 or earlier chassis with a crash box. The mounts and horns vary and adapting the later
box isn't always easy.
Have a look where the gear selector goes into the hole in the pan. It should line up in the middle of the hole and another area to check is that the
axle tubes have plenty of clearance for the boots. It's a good indication that everything is in place.
|
Ah, I didn't read all the replies. Yea, later box in early chassis will require early kombi nosecone or the chassis mount cutting off and relevant
mount for his gearbox welding on.
madness is in the eye of the beholder |
|
|
Deadpan
Seriously Crusin Dubber
Posts: 109
Threads: 24
Registered: April 5th, 2014
Member Is Offline
Location: Brisbane
Theme: UltimaBB Psyche Grey
Mood: 'Super' defensive
|
| posted on June 8th, 2014 at 06:00 PM |
|
|
You have already got a few possible outcomes from suggestions,mine would be if everything is correct and the engine is already out of the bug,pull out
the gearbox and then see if they bolt up
Shaun,Part-time secret snake relocator,full time reptile keeper and small collector of ugly projects bugs ...  |
|
|
