| [ Total Views: 744 | Total Replies: 14 | Thread Id: 106543 ] |
|
|
 landfall
Officially Full-On Dubber
Posts: 290
Threads: 36
Registered: June 4th, 2014
Member Is Offline
Location: Hobart Tassie
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 7th, 2014 at 04:25 PM |
|
|
Inlet manifold removal, 1976 Bug.
Hi all,
I am about to undertake the removal of my intake manifold on my 1600 type 1, so that I can fit dual carbs.
Reading information both here on the forum and in Bentley's it appears to be a mammoth job, hardly worth the effort, but as I now have the carby
kit.......
My question is:- To simplify removal is it possible to cut the heat risers, then if I should want to return to standard at a later date, rejoin them
using high temperature hose or tight fitting copper tubing? Currently they are attached to my exhaust headers. The car is running OK with the
original Solex with this set up, despite aircooled.net and others saying it should not work.
Thanks
Ken
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on July 7th, 2014 at 05:14 PM |
|
|
Ken its a lot easier in the long run to drop engine out to remove the manifold.
good opportunity while its out to do any other small jobs - mainseal, engine bay seal, clutch etc.
Even with the heater risers gone its still a juggling act trying to get it out in the car.
it just takes lifting the fan shroud up and off to get it out once the engine is out.
If your manifold is in good shape the 73-76 ones with the larger diameter heat risers are worth saving, the modern repros are a shitful fit and
quality.
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on July 7th, 2014 at 06:31 PM |
|
|
Yep to Joels post, x 10, and to add that hose or tubing will not work sealing the heatriser if returned to service, only welding would be satisfactory
and all but impossible due to the carbon buildupinternally in the tube
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
landfall
Officially Full-On Dubber
Posts: 290
Threads: 36
Registered: June 4th, 2014
Member Is Offline
Location: Hobart Tassie
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 7th, 2014 at 06:32 PM |
|
|
Thanks Joel,
Have no experience of removing Vee Dub engines and it's not a job I have really got the facilities to do.
I'll have to give it some serious thought, car running OK at the moment.
Ken
|
|
|
hellbugged
A.k.a.: Daimo Pell
23 Windows of Awesome
48's and straight cuts
Posts: 5080
Threads: 116
Registered: April 17th, 2003
Member Is Offline
Location: Nambucca Valley NSW
Theme: UltimaBB Psyche Blue
Mood: Couldn't care less
|
| posted on July 7th, 2014 at 08:01 PM |
|
|
Sounds like youre best off leaving it as is
gather some more experience before diving off to into the "joys" of modifying
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on July 7th, 2014 at 08:14 PM |
|
|
Um, if it's a twin port engine then with the manifold boots undone doesn't the centre section lift out?
Never owned a single carb TP engined Bug before only single port so just wondering?
madness is in the eye of the beholder  |
|
|
landfall
Officially Full-On Dubber
Posts: 290
Threads: 36
Registered: June 4th, 2014
Member Is Offline
Location: Hobart Tassie
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 7th, 2014 at 08:33 PM |
|
|
No unfortunately that is what I thought.
Because it is running so good at the moment I will take advice and leave well enough alone.
When something goes wrong with the engine there will be plenty of time to start modifying.
Bentley goes on about being able to do it by "just" lifting the fan housing. That in itself look like a mongrel of a job.
And I thought mini's where bad enough to work on
Ken
|
|
|
ctefeh
Wolfsburg Wizard
Posts: 479
Threads: 30
Registered: April 23rd, 2005
Member Is Offline
Location: SiddaKnee nowadayz
Theme: UltimaBB Pro Blue ( Default )
Mood: grimly determined
|
| posted on July 8th, 2014 at 11:35 AM |
|
|
Centre section removal
Ken,
X 10 as well on all of the above. "If it aint broke - don't fix it". Count yourself lucky that at least you have an alternator stand.
The Bentley people have 1000 trained 3 armed, small handed chimps with all the tools of VWoA at their disposal.
Enjoy
Ctefeh
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on July 8th, 2014 at 01:00 PM |
|
|
| Quote: | Originally
posted by landfall
Bentley goes on about being able to do it by "just" lifting the fan housing. That in itself look like a mongrel of a job.
|
Lifting the fan housing is all it takes but doing that in the car is easier said than done.
All the ducting off the oil cooler has to be removed (by feel too), lots of skinned knuckles on the spikes holding the tarboard.
The thermostat flaps if they still exist need disconnecting and throttle cable and guide tube removed.
trying to do all that in the car is more hassle than removing the engine.
You won't believe how heavy an alternator can feel when you are trying to juggle a fan shroud back into place.
|
|
|
landfall
Officially Full-On Dubber
Posts: 290
Threads: 36
Registered: June 4th, 2014
Member Is Offline
Location: Hobart Tassie
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 8th, 2014 at 04:57 PM |
|
|
Thanks Joel and others.
After having a good look around, "Yes I would" I am in agreement
that it WOULD be easier to take engine out.
Had a look at a utube video on taking the engine out, looks easy
except of course the video was of an earlier model, no oil cooler etc and you could see the two upper bolts. No sign of them in my car????
Ken
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on July 8th, 2014 at 08:48 PM |
|
|
The drivers side top one is exactly the same but with the top left one its a bolt and you undo it from the gearbox side.
There is a captive nut in the case so you just undo the bolt from underneath, much easier than the early models.
|
|
|
landfall
Officially Full-On Dubber
Posts: 290
Threads: 36
Registered: June 4th, 2014
Member Is Offline
Location: Hobart Tassie
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 9th, 2014 at 04:01 PM |
|
|
Thanks Joel,
Carby package arrived today after I put everything back to normal. Damn, I might as well have kept going I had nearly everything undone. Getting the
car high enough to get the engine from under will be the problem though.
Will continue to keep driving the car until something else need doing, then it will become removal time.
In the meantime I will have another look about and familiarize myself with the beast.
Front suspension/shock absorber problem needs to be addressed yet.
Ken
|
|
|
waveman1500
Custom Title Time!
Also rides a Honda
Posts: 1346
Threads: 13
Registered: December 17th, 2009
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 9th, 2014 at 11:36 PM |
|
|
You can do it on a garage floor with a big enough pair of axle stands, I bought a pair that were rated to 4000kg, intended for 4x4s. You will need a
decent trolley jack as well, I had to stack wooden blocks on top of mine to lift the car high enough.
The actual job of removing the engine is easy, the first time took me a few hours and on my second time I got the engine out in half an hour!
|
|
|
Joel
Scirocco Rare
Now containing 100% E-Wang
Posts: 9368
Threads: 211
Registered: February 14th, 2006
Member Is Offline
Location: Northern Rivers NSW
Theme: UltimaBB Pro Purple
Mood: Tact Level 0.00
|
| posted on July 10th, 2014 at 07:46 AM |
|
|
That's the joy of a removable valance, you don't have to worry about height
|
|
|
landfall
Officially Full-On Dubber
Posts: 290
Threads: 36
Registered: June 4th, 2014
Member Is Offline
Location: Hobart Tassie
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 10th, 2014 at 05:00 PM |
|
|
660mm, that's achievable, thanks.
I love the removable valance idea.
Managed to find a great utube video that the vw specialist showed a motorbike lift being used to remove and lower the engine. At the moment Supercheap
are selling the same lift for $109, could save a lot of mucking about and swearing.
Thinking I could fabricate a frame to hold the engine in place.
Any more comments are welcome.
Ken
|
|
|
