| [ Total Views: 11380 | Total Replies: 77 | Thread Id: 106613 ] |
| Pages: 1 2 3 |
|
|
 nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on July 15th, 2014 at 09:26 AM |
|
|
My last Toy
Starting to get some stuff together for my last project I plan on doing.Got the shits on with the Drag Car at the moment.Got sick of being pissed
around by "experts".When I get it ready to run again,I will hook up with Pat at CB to finish it off.Going to send this wheel, button and flasher
switch off to have a black pearl finish with a red flame through it.I already have a rear disc brake conversion I made from new ED Falcon stuff with a
5x130 bolt pattern and a new set of front rotors from Sherman for a link pin front-also in 5x130,as well as a set of dropped spindles.I will buy some
of those 17x7 copies of the Fuchs alloys.Looks like I will be able to use some stuff laying around here.Have to do an IRS on the pan and cut it to fit
a Bus auto trans I have left over from the Drag Car.I have put new bearings in the diff,but will get the 003 auto overhauled.I have a 54 in fairly
rough shape I got from 57 oval that will be suitable for some radical cutting and modifying.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
HappyDaze
A.k.a.: Greg Mackie
Son of Jim - Creator of Good
Superannuated
Posts: 2887
Threads: 141
Registered: June 13th, 2009
Member Is Offline
Location: Southern Highlands NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Happy enough
|
| posted on July 15th, 2014 at 09:40 AM |
|
|
Should be ready for Valla then, Gary. 
I'd rather wear a Beetle out by racing it than by polishing it!
|
|
|
Turbo54
Veteran Volks Folk
Posts: 2220
Threads: 268
Registered: July 13th, 2004
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
Mood: Boost'n
|
| posted on July 17th, 2014 at 09:40 PM |
|
|
Whats the rough 54 shell look like? Not my old one is it?
T54
C'mon kids gather round,
there's a new sensation hitting town,
It's moving straight, low to the ground,
it'll pick you up when your feeling down.
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on July 17th, 2014 at 10:07 PM |
|
|
No- it had been laying here for many years. The doors are in excellent shape which for me is the big bonus. The rest is all fairly easy to fix.
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on July 18th, 2014 at 08:56 AM |
|
|
Sounds interesting....... enjoy the journey.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on July 18th, 2014 at 11:09 AM |
|
|
Yes-looking forward to it.The plan is to reproduce my Drag Car in a street version from the 54 with a Suby turbo and the spare Bus auto I have.Got to
finish the closed in trailer for the Drag car first though.
|
|
|
20bkombi
Wolfsburg Wizard
Posts: 597
Threads: 26
Registered: March 2nd, 2009
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 19th, 2014 at 09:01 PM |
|
|
Sounds very cool Gary!!.
I too, want to build a street notch back with the same engine and trans as my unfinished drag notch.
You might want to make the primary pressure valve work off the throttle cable as it might not work under boost.
I love watching new projects take off.
AARON'S SPEED SHIFT AUTOS
Specialising in Vw automatic transmissions, differentials and torque converters
Stock or modified to suit your application (street, drag, off road)
Ph 0402 233 027
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on July 19th, 2014 at 10:10 PM |
|
|
You will be a part of the journey Aaron- the transmission will be your project when the time comes. I was going to use the Bus Trans with the 003 .
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on July 24th, 2014 at 02:31 PM |
|
|
Bought another tool for the workshop-only a small version,but what an amazing thing to use.I have just cut some 6mm 316 stainless and just like a hot
knife thru butter.Cleaned up the torsion bar tube for the new ute and modified the jigs I made for the Drag Car-will still be 100mm longer but only
60mm lower this time.The 90mm I did on the Drag Car is a bit too low for a street car.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on October 31st, 2014 at 02:26 PM |
|
|
Something has got in the way of this toy-fibreglass shortened buggies.I have done full rebuilds of 2 in the last 2 months for customers,and somehow
have ended up with 2 of my own.I have almost finished cutting and shutting my new pan and have done things a little differently to the norm.I have
recently done a pan shortening for a customer,and got the idea of cutting the full rear floor out like I did to my Drag Car,and replacing it with a
flat steel panel.Saves having to piss around trying to get the join in the OG pan welded up-way too thin for a good finish.I have done the same in my
pan,but went to 2mm plate instead of 1.6.It's so much easier to weld and cuts unreal with the plasma.I have bought almost everything new for
mine-eg,new 7inch stainless headlights,all new tie rod ends,stainless cannon exhaust,50mm ally mill finsh tube for roll bars,extruded ally channel to
make a new taller windscreen and all new VW style dash switches.I am having a double sider IRS box converted to swing axle,so gives me a 3.88 diff for
better cruising with the 1600 twin port.I had a spare LH Drive 22mm master cylinder left over,so I have converted the pan to take LH and RH drive
cylinders.The LH drive ones are a fraction of the cost of RH versions.I have cut the gear lever base from the tunnel and shifted it back so it sits in
the same position as the Super Bugs.Will modify a short hand brake lever to take the early type cable attachment.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on October 31st, 2014 at 02:33 PM |
|
|
A couple more.The buggy I have almost finished for a customer-he wanted a 2inch lift kit,so I made the whole thing from 50X25X2mm ally RHS.Turned out
fairly good-but a lot of cutting and welding.His is a yellow Manx style body.I made a full trans/engine sump guard and a round bar rear protection set
up.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on October 31st, 2014 at 02:38 PM |
|
|
The body lift kit.I made the kit so it can be bolted to the pan in its correct location with the seal under it,then the body can go on and be bolted
thru the normal body attaching holes.I have done a 30X30X2mm square tube strengthening beam under both pans where the body bolts down and plug welded
it to the pan between each of the body attaching holes.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on October 31st, 2014 at 02:54 PM |
|
|
Some more.I have 2 38mm holes each side of the back of the pan.I have ordered some stumpy stainless marine drain plugs to put there-should be a lot
easier to hose it out after a day in the sand-just get the front up a bit higher and unscew the plugs.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on October 31st, 2014 at 02:57 PM |
|
|
Holes in pan floors and the seat belt anchors welded in.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on October 31st, 2014 at 03:09 PM |
|
|
The clutch cable tube had broken at the pedal end,so I had to cut the pan open to fix that,and because I was using a set of Super Bug pedals,I also
had to shift the tube over to the passenger side.All worked out good.I added 2 more braces to connect the clutch tube to the pan along the tunnel-so
it should never move any more.While I had the tunnel open,I ran a new 8mm fuel line and bought it out the LHS of the pan.Doesn't get in the way of
any steering arms or fuel tank fittings.I machined some chrome moly tube so the OG hand brake cable tube would slip inside,then welded the C/M tube to
the pan and the handbrake bracket.Just pushed the steel tube in from the rear and hit it home,welded it to the C/M and cut the excess off at the frame
horn.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
modnrod
Fahrvergnugen
Posts: 978
Threads: 50
Registered: March 17th, 2011
Member Is Offline
Location: Midwest, Westoz.
Theme: UltimaBB Pro Blue
Mood: Old School Volksies!
|
| posted on November 1st, 2014 at 01:22 PM |
|
|
Can I ask a question please?
Is the 30 x 30 a perfect fit into pan bolting channel, or does it have a few mm slack once sitting in the channel?
Did you need to weld in crush tubes for the pan-to-body bolts, or isn't there enough torque on the bolts to matter?
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on November 1st, 2014 at 05:27 PM |
|
|
Not a snug fit- but I keep it tight against the inside edge of the pan. There are long raised sections in the pan channel-so keeping it hard against
the pan edge keeps it all square.I drill 13mm holes in the pan so I can plug weld the tube to the pan- it seems ironical, but where I need to drill
the 13mm holes is where the holes are left from the small spikes used at the factory to hold the body seal rubber in place. I cut about 20 slits in
the tube with a 1mm disc to create the bend, then clamp it all in place and make a cardboard template of the bend, cut a piece from 3mm flat and cover
all the slits and weld it all up.Of course I pre drill all the holes for holding the body down. I drill them 10mm and use a heavy 8mm flat washer
underneath- never had the tube crush yet.
|
|
|
vduboy
Insano Dub Head
Posts: 702
Threads: 41
Registered: October 6th, 2012
Member Is Offline
Theme: UltimaBB Streamlined2
Mood: Dying to get more buggy building time..
|
| posted on November 7th, 2014 at 10:26 AM |
|
|
Funny you should mention crush tubes in the lift kit, my engineer made me put them in every body to pan hole, even though I'm 100% sure the
fibreglass would crack before the lift kit would crush... Love
your work mate! Looks great, got a link to the drag car? Or still a sore point?
It will all be OK in the end, if it's not OK it's not the end!
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on November 7th, 2014 at 01:13 PM |
|
|
You are correct about it destroying the fibreglass way before crushing the tube.I used 2mm wall thickness, but reckon you could get away with 1.6 at a
pinch.I put the bodyon the yellow one last week- you cant actually do the bolts up tight because the fibreglass starts to come apart, so I used nyloc
nuts on everything and it seems all OK.Check in the "Drag Racing" section for the Drag Car- "another toy for me"
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on November 8th, 2014 at 04:17 PM |
|
|
Picked this Ghia clock up from Ebay-bady burnt out-probably 12volts put to a 6volt unit.Put in a 1.5 volt battery clock to replace the
original.modified some hands to suit and now have a working unit.Used a glass from a 6volt speedo to replace the plastic OG one with the adjusting
hole.Will use it in my Manx buggy.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
57 oval
Seriously Crusin Dubber
Oval type 4 Fuel Injected
Posts: 184
Threads: 48
Registered: February 5th, 2008
Member Is Offline
Location: Whyalla
Theme: UltimaBB Pro Grey
Mood: Oval
|
| posted on November 8th, 2014 at 05:11 PM |
|
|
Clocks fast Gastro your post was 417pm and the clock reads 435pm ???
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on November 14th, 2014 at 12:26 PM |
|
|
Picked up my shortened buggy pan this morning after a blast and fresh paint.Very happy with the finish.Have finished an IRS rear disc brake conversion
for my Hot Rod with Ford stud pattern and I am halfway thru a swing axle conversion using the Ford stuff-but got new undrilled rotors some time ago
and drilled for Porsche stud pattern.I bought new front rotors from Sherman years ago in Porsche,so have cleaned them up,fitted 14mm studs and painted
ready to be fitted.I have ordered some new rotors from John in Ford stud pattern for my Hot Rod project.I already have 2 15x6 Fuchs for the Buggy and
bought 4 15x5.5's last week from a bloke in Sydney,which I will use 2 for the front of the Buggy.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on November 14th, 2014 at 12:45 PM |
|
|
I modified some Super Bug high back seats by fitting the runners from early seat bases so they would fit the seat frames on my 6volt pan. I found that
they wouldn't slide right back on a shortened pan, because the backrest adjusters hit hard on the centre tunnel.I cut some reliefs into the tunnel
and fabbed some steel plates to fill the holes I had to cut.Works really good now with full travel.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on November 28th, 2014 at 01:19 PM |
|
|
Started to assemble the Buggy pan.Made all new brake pipes and modified some to make the LHD master cylinder fit.I have filled every cavity that can
hold moisture with Fish Oil-things don't smell too good at the moment.Stripped a late pedal set,sand blasted,painted and lubed up for years of
trouble free use.I modified the clutch pedal with a gusset welded where it attaches to the pivot shaft and bent it to sit closer to the tunnel-it was
way too close to the brake pedal.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12755
Threads: 731
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 28th, 2014 at 09:06 PM |
|
|
That pan looks sweet !
Futue te ipsum!!!
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on January 14th, 2015 at 08:18 PM |
|
|
Have got a problem with the buggy body-I mounted it on the pan and it hangs low on the LH rear corner-about 35mm.I checked the pan for squareness-and
it had pulled about 25mm low on the RH side where I welded in the 30x30 reinforcing tube.I don't remember it being out before I had it blasted and
painted.I checked with straight edges and spirit levels-and the front frame head had pulled also by 15mm low on the RH side.I took the pan to a shop
with a 3x2 metre by 300mm thick cast plate.I blocked it up level,strapped it down and jacked it until it all squared up.I now have less than 2 mm
twist from front to rear.Back to the fibreglass body-on a flat surface,it has 35mm difference from floor to each rear corner.It must have been made
like that - because its only as good as the mould it came out of.I has a Fibreglass Bloke look at it today and he has taken on the job to fix it.He
has had me make a slit right along the LH side,about 70mm up from the mounting flange,bolt it all back down and support the body to set it at the
correct height.All done and it looks way better now.Off tomorrow to have him fix it.I have put black plastic right around the join on the pan,to stop
any resin stuffing up my newly painted pan.Has anybody ever had a body this out of square.I have finished 2 major buggy rebuilds lately-2 different
types of bodies,and both hung low at the LH rear corner-but not as bad as mine
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on February 12th, 2015 at 09:40 PM |
|
|
Have got the body back from the fibreglass bloke,very pleased with the work.I have got a lot to do now with sanding,bogging and high build primer.I
have made a frame to go under the trans and engine for sump guards as well as incorporating a towbar and protection bars.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
adlbeetle66
A.k.a.: Denver
Custom Title Time!
Under the car.........again!
Posts: 1476
Threads: 98
Registered: August 15th, 2014
Member Is Offline
Location: Capalaba, Brisbane, QLD
Theme: UltimaBB Streamlined2
Mood: ICH BIN VW NUSS
|
| posted on February 13th, 2015 at 07:39 AM |
|
|
Neat work!
Keep it up!! 
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on February 18th, 2015 at 05:31 PM |
|
|
Have started to mount the body to the pan.The body seems fairly short over the motor compared to others I have seen.I had the spare wheel cavity
glassed up to make an on board esky.Should hold a couple of sangas and some beers.Will put a padded and hinged seat over it.Just fitted the boat bung
to let out the water.This body won't allow the carby and air cleaner to go under it-hence the big bit cut out when I bought it.Will solve that issue
with some Type 3 twin carbies.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
nbturbo
Veteran Volks Folk
Posts: 2171
Threads: 89
Registered: December 19th, 2002
Member Is Offline
Location: Whyalla Sth.Aust.
Theme: UltimaBB Powder
|
| posted on March 21st, 2015 at 08:42 PM |
|
|
Got a few more jobs done on the Buggy.I have finished the rear protection bar/towbar and it is away being blasted and painted.Made a trans and engine
skid plate from 6mm ally checker.The body won't allow the standard centre carb so I have fitted a set of Type3 duals and had to fabricate the full
throttle assembly.I did use part of the Type3 centre pull.Just finished doing a rear disc conversion on a Type3 trans using ED Ford stuff.Bought a
pair of new undrilled rotors and drilled them 5x130.Bought some new front rotors from Sherman for the link pin beam also 5x130.Can now use some of the
spare Fuchs 911 rims I have.Will probably buy a new set of 17x7"s for the rear and use some 15x6's on the front.My buggy had no dash when I bought
it,but I was doing body off/new floorpan resto at the same time on a customers Buggy.His dash was a perfect fit to my body.His was full of holes which
were no longer being used-so I sent it away to have all holes filled and then a mould made from it-I now have a new clean skin dash for mine and a new
mould.
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
|
|
|
| Pages: 1 2 3 |
