| [ Total Views: 1076 | Total Replies: 9 | Thread Id: 111526 ] |
|
|
 Yogie
Super Moderator
Posts: 1603
Threads: 108
Registered: June 7th, 2003
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue
|
| posted on September 5th, 2016 at 05:05 PM |
|
|
No spark on my beetle - Problem solved
Hi everyone
I drove my beetle yesterday (68 1600 with pertronix electronic ignition) and then when I came back about 6 hours later, it wouldn't start. No spark
at all. I poured some fuel in to the carby in case it was not getting fuel and still nothing.
Any suggestions for me to try?
Yogie
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on September 5th, 2016 at 05:45 PM |
|
|
check the fuse and wiring
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12757
Threads: 732
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 5th, 2016 at 08:17 PM |
|
|
Do you have a multimeter?
Are you getting power to the coil?
How do you know you are not getting spark?
How did you test it?
Is the carbon button bit in the cap shagged?
Futue te ipsum!!!
|
|
|
Yogie
Super Moderator
Posts: 1603
Threads: 108
Registered: June 7th, 2003
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue
|
| posted on September 5th, 2016 at 09:29 PM |
|
|
I am guessing no spark as the engine turns over but does not try to kick at all. I wasn't sure if it was because of a lack of fuel or something else
so I put fuel directly in to the carb and it still just turned over with no sign of spark/kicking at all.
I do have a multi meter but not sure what to look for when checking the coil.
Yogie
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12757
Threads: 732
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 5th, 2016 at 09:43 PM |
|
|
2 wires on coil
One is permanently 12v when ignition on
Other one goes to condenser
Check to see if the 12 v is there
Get some one to help you kick it over and with a plug lead pulled at the dist cap (hold carefully with insulated pliers) go to put lead back in the
cap while mate is turning over
If you have spark you will see it
Futue te ipsum!!!
|
|
|
Yogie
Super Moderator
Posts: 1603
Threads: 108
Registered: June 7th, 2003
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue
|
| posted on September 6th, 2016 at 06:42 AM |
|
|
Thanks Bizarre. I will give that a try.
Yogie
|
|
|
 68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on September 6th, 2016 at 06:21 PM |
|
|
Hi
Using a multimeter the Ohms measurement between both screw terminals on the coil [with all leads to coil disconnected] the measurement should be
approx. 3 to 5 ohms..
Something else to measure is the rotor button in the distributor..
From center to end... it should be the same as touching the ends of the meter leads together, or if it is a genuine VW Bosch rotor button it will show
some resistance in Ohms as they do have a resistor in the rotor arm between the end and the center. I have heard of this resistor burning out, leaving
an open circuit.. and no spark..... The other culprit that can stop ALL spark is the condenser....
It pays to renew the distributor cap, rotor and points and condenser and keep the old ones [if they were OK] in the car for spares.
Another one to look for if all the about test out OK, is the hi voltage cable from the coil to the distributor. If this has wire thru the center of
it, then it will be OK, if it has something else thru the center of it, it can be burnt out... You can test it with Your multimeter...
Best of Luck
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
Yogie
Super Moderator
Posts: 1603
Threads: 108
Registered: June 7th, 2003
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue
|
| posted on September 11th, 2016 at 06:03 PM |
|
|
Problem solved. vw54 was right. I had checked the fuses and they looked fine. Put the multimeter on the coil and 1.2v only. Thought it may be the
immobiliser but that was working properly.
Checked the fuses again and the coil fuse had 11.8v on one side of the terminal and 1.2v on the other. Cleaned the terminal and all is good.
Thanks everyone.
Yogie
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on September 12th, 2016 at 06:05 PM |
|
|
Good result Yogie...
All copper and brass electrical nuts terminals fusebox fuse terminals all get contaminated over the years and even though they may be connected...
there maybe NO actual connection or high resistance there.
it doesn't happen overnight but it does happen
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on September 13th, 2016 at 08:23 AM |
|
|
multi meters have their uses but for a problem like this where you need to load the circuit a dirty old test light is the best thing to use, getting a
1.2 volt reading on one side of the fuse confirms this
|
|
|
