| [ Total Views: 1131 | Total Replies: 8 | Thread Id: 111938 ] |
|
|
 rasp_pi
Learner Dubber
Posts: 5
Threads: 2
Registered: December 21st, 2016
Member Is Offline
Theme: UltimaBB Pro White
|
| posted on December 22nd, 2016 at 12:39 PM |
|
|
carb issue?
Hi all,
first post here, likely not the last.
Recently taken possession of 69 bug, with a 1300 (not original engine, I might add) and a 30-pict-1 carbie. Or maybe a -2. Can't remember now (car
not here to have a peek at).
I got the engine turned over, and it idled OK after warming up. It hadn't been started in probably 18 months. Anyway, i tried opening the throttle
but it would quickly lose power and begin to sputter out. If I backed off on the throttle, it would recover and idle. It revs only up to a point.
The choke butterfly was fully open and the air filter was off. I thought perhaps a blocked jet?
So I tried revving the engine and choking the carbie with a rag to suck out any blockage. Didn't work.
Any ideas? |
|
|
splitbus
Seriously Crusin Dubber
Posts: 162
Threads: 12
Registered: January 22nd, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 22nd, 2016 at 05:33 PM |
|
|
Maybe the advance on the dizzy not working
Cheers, Mike
------------------------------------
| o*/o | 55 split screen
I don't have a bucket list, I have a f^%k it list a mile long
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on December 22nd, 2016 at 06:43 PM |
|
|
TBH if it's been sitting for 18 months then the petrol will be knackered and can cause it's own issues but it is likely that the petrol has sludged
and tarnished the inside of the carb. I'd recommend a can of carb cleaner and a full strip down.
To check if the vac dizzy is working then take the cap off and suck on the vac pipe. You should see the advance plate move. If it don't then try to
manually turn the plate. If it turns then likely the vac can diaphragm is perforated. Remove it from the dizzy and suck on it. the arm should move
easily and return when you stop sucking. If the advance plate didn't move then it could have got stuck to the dizzy shaft. Soak in Plusgas or similar
rust penetrating fluid. WD40 can work but it's a water dispersant and not a rust penetrator.
Another thing is fuel delivery. The pump may be able to supply enough fuel for idle but nothing more than this. Smell if the oil has a petrol
odour.
Don't try and cut corners with the carb. YOu want a solid baseline to work from and if you don't give it a proper clean you can be chasing your tail
for a very long time 
madness is in the eye of the beholder  |
|
|
rasp_pi
Learner Dubber
Posts: 5
Threads: 2
Registered: December 21st, 2016
Member Is Offline
Theme: UltimaBB Pro White
|
| posted on December 22nd, 2016 at 07:38 PM |
|
|
thanks for the replies!
I had forgotten the diaphragm on the dizzy. I'll certainly try the vac pipe. The advance plate did move by pressing it down, but that doesn't test
the diaphragm.
regardless, as psimitar mentioned, carbie probably won't be very clean anyway. I've done some reading up on carbie strip-down.
I had thought of the fuel pump being not up to the task, but didn't know how to test it. petrol-flavoured oil, you say? another noob qn- why would
this be the case?
its all learning, right?  |
|
|
pv370
Officially Full-On Dubber
Posts: 272
Threads: 38
Registered: April 7th, 2014
Member Is Offline
Location: Goulburn NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Southern Comfortably Numb
|
| posted on December 23rd, 2016 at 01:49 PM |
|
|
a pin hole in the fuel pump diaphragm can cause lack of fuel delivery and "petrol flavoured oil" as you put it because the fuel leaks through the
pin hole and runs down inside the case into the oil.
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on December 23rd, 2016 at 07:07 PM |
|
|
Yup, what PV370 said. The only other way to test a fuel pump is with a pressure gauge and then you'll need a t-piece and extra piping. Not something
the home mechanic keeps in his toolbox.
madness is in the eye of the beholder |
|
|
ACE76
Seriously Crusin Dubber
Posts: 105
Threads: 19
Registered: August 4th, 2005
Member Is Offline
Location: Victoria
Theme: UltimaBB Pro Purple
Mood: ACE 30 FOR SALE!
|
| posted on December 26th, 2016 at 05:07 PM |
|
|
Also check if the fuel filter (if fitted) is clean/clear and not gummed up (hard to see). And that the fuel line allows clean petrol to flow out
freely (and not water, dirt etc., which can collect at low points).
ACE 30 & ACE 40 oil: specially formulated for your Air Cooled Engine...
Delivery free Outer Eastern Melb. & Dandenong Ranges.
from$19 for 2.5L (spot-on for 1 fill, re-use bottle to measure), or $29 for 5L (2 fills)
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on December 26th, 2016 at 06:13 PM |
|
|
Drain the tank and put in new petrol
Also as above check the dissy vaccum to see if its working
|
|
|
rasp_pi
Learner Dubber
Posts: 5
Threads: 2
Registered: December 21st, 2016
Member Is Offline
Theme: UltimaBB Pro White
|
| posted on January 28th, 2017 at 08:02 PM |
|
|
hey guys,
thanks for the advice,
an update on it: yep, checked filter and replaced (was pretty dirty). Ended up replacing the vacuum line on the dizzy as the rubber had pretty much
fallen away. I'm guessing it wasn't making much of a vacuum...
However, was still having the same issue
So, going back to the carbie. Got a rebuild kit. Now just need to take a deep breath and try that. |
|
|
