| [ Total Views: 567 | Total Replies: 4 | Thread Id: 14514 ] |
|
|
 karmannghia60
Custom Title Time!
Karmann Ghia Sucker
Posts: 1459
Threads: 388
Registered: August 27th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 15th, 2003 at 10:21 AM |
|
|
Removing/replacing front beam
This is on my '60 Ghia. Would removing the fuel tank make the job easier? Do I get better access to the top nuts? The PO welded the top of the
beam to the frame head so I need to cut through it with an angle grinder or something. I can't see how I can do that from under the car!
Raf
[Edited on 15-10-2003 by karmannghia60]
|
|
|
wadd
Seriously Crusin Dubber
Posts: 179
Threads: 41
Registered: April 6th, 2003
Member Is Offline
Location: Mt Isa Qld
Theme: UltimaBB Pro Blue ( Default )
Mood: sunny
|
| posted on October 15th, 2003 at 10:36 AM |
|
|
it does on a beetle ...no help i know if tank is over the front beam it may be the same as
|
|
|
geodon
Wolfsburg Wizard
Posts: 478
Threads: 63
Registered: August 28th, 2002
Member Is Offline
Location: geelong
Theme: UltimaBB Pro Blue ( Default )
Mood: stumbling
|
| posted on October 15th, 2003 at 12:31 PM |
|
|
Alot easier
Seeing it's so easy to remove the tank, why not?
Also if you are using a trolley jack to lower it, you can stand over the top & steady it as it goes down.
Geez, I bought a 62 beetle 30 years ago that had that done to it, supposedly to stop front end shimmy. Take a good hard look at it- there may be be a
bent frame head involved.
[Edited on 15-10-2003 by geodon]
|
|
|
karmannghia60
Custom Title Time!
Karmann Ghia Sucker
Posts: 1459
Threads: 388
Registered: August 27th, 2002
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
|
| posted on October 15th, 2003 at 02:11 PM |
|
|
Why would they weld it if it was a bent frame? I thought maybe the frame was rusted where the bolts go through but its not the case. I had a good look
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on October 15th, 2003 at 03:28 PM |
|
|
Karmann Ghia60
The PO or whoever did it may have just bought a new welder... why else would You do it... Maybe they thought that 6 bolts were not enough to hold the
front end into place....
Yes, with the Beetle its MUCH easier with the tank Out... I have just done mine, replaced everything on the front end, ball joints tie rod ends etc...
I now have the tank in, and its nearly impossible to do anything... and don't forget the top two bolts on the opposite side of the torsion bars..
You can get New rubber blocks from Mick Motors... cheers.. Lee
| Error |
| Sorry, you must be a registered user in order to download attachments. |
|
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
geodon
Wolfsburg Wizard
Posts: 478
Threads: 63
Registered: August 28th, 2002
Member Is Offline
Location: geelong
Theme: UltimaBB Pro Blue ( Default )
Mood: stumbling
|
| posted on October 16th, 2003 at 09:24 AM |
|
|
If I remember rightly, it had had a head on & been fixed. The mounting bolts were not able to fix the FE on firmly enough to prevent the steering
wheel ( & front wheels?) shimmying & car repairers I spoke to at the time said welding the FE on was a way around it. So why was yours welded
on in the 1st place? Mounting bolts stripped perhaps??
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on October 16th, 2003 at 10:09 AM |
|
|
YES remove the fuel its only 4 bolts and the hose.
this way you can get to the tie rod ends easier as well.
|
|
|
