| [ Total Views: 673 | Total Replies: 4 | Thread Id: 92121 ] |
|
|
 chillihilli
Commited Dubber
Posts: 64
Threads: 19
Registered: October 13th, 2010
Member Is Offline
Location: Melbourne Victoria
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 13th, 2011 at 06:30 PM |
|
|
1600 end play
Hi there. I am a ways throughout my autostick replacement, and got some good advice to change the main oil seal whilst the engine was out (thanks Lee
: . As I was prising out the oil seal, I felt a clunk and thought "oh
dear" or words to that effect. I discovered I could move the crankshaft with a screw driver at the front if the engine (flex plate side ) with a
screw driver, and by hand with the main pulley. It's a good 2 or 3 mm. I'm pretty sure this is well outside the tolerances. The produces reasonable
power, blows a little smoke etc
My question is should I look at a rebuild? My original plan was to replace the trans and put it all back together whilst I save up for a new enigne,
but am I wasting my team reassembling and just bite the bullet and get it done. Anyone have experience on approx cost for a stock 1600 rebuild?
Thanks in advance!
71 Clementine Superbug Autostick
|
|
|
Menangler
A.k.a.: Dave Becker
Custom Title Time!
Posts: 1991
Threads: 309
Registered: August 26th, 2002
Member Is Offline
Location: South Coast NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 13th, 2011 at 07:42 PM |
|
|
If you felt the clunk when the flex plate was off, that is perfectly normal, you should have no noticeable play when it is all bolted back together.
FAHRVERGNUGEN;
Description of a pleasurable sensation,
Experienced when a car and it's driver are in mutual harmony, A unique driving experience, Pleasure, Satisfaction,
A feeling experienced by Volkswagen Drivers.
 |
|
|
mactaylor
Custom Title Time!
Posts: 1005
Threads: 54
Registered: August 14th, 2007
Member Is Offline
Location: Albury
Theme: UltimaBB Pro Blue
Mood: even my dog is german
|
| posted on August 14th, 2011 at 06:57 AM |
|
|
bout 4 to 6 thou is the number your chasing with the gland nut to spec.
EVERLAST CONCRETE TANKS
1800 552 123
|
|
|
chillihilli
Commited Dubber
Posts: 64
Threads: 19
Registered: October 13th, 2010
Member Is Offline
Location: Melbourne Victoria
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 14th, 2011 at 08:48 AM |
|
|
Phew! Thanks for that. I will get the seal done and check it when reassembled.
71 Clementine Superbug Autostick
|
|
|
bevoracing
A.k.a.: Tony Beven
Officially Full-On Dubber
Posts: 326
Threads: 36
Registered: January 18th, 2009
Member Is Offline
Location: Mount Pleasant SA
Theme: UltimaBB Vintage
Mood: Leaning against the shed wall !.
|
| posted on August 14th, 2011 at 08:56 AM |
|
|
Need to put the gland nut in there, without the flex plate, then lever the crank up and down and in and out. Make sure the bearing is not moving in
the case. If it moves you need a rebuild. Might as well carefully check it while you’re there. You can’t control the end play or keep the oil
in it if the bearing is moving.
Good luck. Tony
|
|
|
