| [ Total Views: 714 | Total Replies: 7 | Thread Id: 97234 ] |
|
|
 shaihulud
Custom Title Time!
Posts: 1448
Threads: 197
Registered: November 4th, 2005
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 3rd, 2012 at 04:46 PM |
|
|
Tin ware missing from engine
I'm in the process of re-assembling a 1600 TP into which I have fitted a new set of rings.
I've nearly completed the job to discover that I failed to fit those two small pieces of tin ware that fit under the barrels on each side and which
clip to the head studs.
I can't fit them now as the push rod tubes are in the way.
I'm not looking forward to pulling the engine apart to fit them.
Will it matter if I leave them out?
The engine will go into a buggy, so not all of the other tinware will be re-fitted and the engine will be sort of out in the breeze.
Is it critical that they are there, or is it O.K. to leave them out?
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12757
Threads: 732
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 3rd, 2012 at 04:53 PM |
|
|
Yes it does matter as they direct air.
What I have done though is to drill a hole in it about 6 or 7mm in dia
hammer the clips flat and slide it in to where it should go.
Them get a LONG 6mm bolt with some LARGE washers and feed down from the top.
Not the best - but it is an answer that worked for me
Futue te ipsum!!!
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on June 3rd, 2012 at 05:02 PM |
|
|
| Quote: | Originally
posted by shaihulud
I'm in the process of re-assembling a 1600 TP into which I have fitted a new set of rings.
I've nearly completed the job to discover that I failed to fit those two small pieces of tin ware that fit under the barrels on each side and which
clip to the head studs.
I can't fit them now as the push rod tubes are in the way.
I'm not looking forward to pulling the engine apart to fit them.
Will it matter if I leave them out?
The engine will go into a buggy, so not all of the other tinware will be re-fitted and the engine will be sort of out in the breeze.
Is it critical that they are there, or is it O.K. to leave them out?
|
without those air directors air won't go round the cylinders
and Yes its easy to leave them out and they should be made to slide in afterwards..lol
do what bizzare said.. save You a lot of work..
when You look at type 3 cool tin.. which does the same job.. they are very different..
but something does need to be in there
cheers
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
LUFTMEISTER
Veteran Volks Folk
Posts: 2041
Threads: 119
Registered: July 13th, 2005
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
Mood: BRISVEGAS in a state of flux
|
| posted on June 3rd, 2012 at 06:05 PM |
|
|
Fit or cook the motor = your call 
Customer service is not dead in Australia.
Always after HAZET & MATRA & VW factory tools
|
|
|
sander288
Custom Title Time!
"Bolt-on Master"
Posts: 1404
Threads: 183
Registered: August 26th, 2008
Member Is Offline
Location: Norman Park, QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: This is my bug. There are many others like it, but this one is mine.
|
| posted on June 4th, 2012 at 12:20 PM |
|
|
^^^^ 
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on June 4th, 2012 at 12:54 PM |
|
|
Fit them and the lower sleds (even in a buggy) or your barrels will not stay round due to uneven temperatures. Out of round barrels = excessive
blow-by high crankcase pressures, leaking oil, shorter engine life, etc etc etc......
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on June 4th, 2012 at 03:13 PM |
|
|
They direct air around the cylinders
otherwise all air is lost...
When You said buggy I was thinking an offroad buggy
but if its a road car and going to do a lot of miles/klms
I would undo the work You have done and put them in
they may not look much but essential for the cooling of the cylinders otherwise the air will just flow past the cylinders..
and the bottom plates need to be there as they are air directors also.. they also direct air over the push rod tubes which help cool the oil flowing
in them..
cheers
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
shaihulud
Custom Title Time!
Posts: 1448
Threads: 197
Registered: November 4th, 2005
Member Is Offline
Location: Perth
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 4th, 2012 at 11:59 PM |
|
|
Thank you gentlemen.
I went to the trouble of removing the heads and pushrod tubes and fitted those small plates in their right positions.
As the engine was on the bench and all the bits were clean and well oiled it was a very quick job to do it.
Having thought about it, it is obvious that they cause the air to travel sideways and cool the barrels, otherwise the air would just rush past,
between the barrels and away without doing much cooling.
|
|
|
