| [ Total Views: 3122 | Total Replies: 4 | Thread Id: 98397 ] |
|
|
 THUDKNUCKLE
A.k.a.: James Stoodley
Officially Full-On Dubber
Posts: 224
Threads: 25
Registered: April 19th, 2005
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Crazy
|
| posted on August 16th, 2012 at 09:38 PM |
|
|
2.5 inch narrow link pin beam with 2.5 inch widened arms ?? any forseen problems
Hey guys just after any wise words or oppinions on as stated above using a 2.5 inch narrowed link pin beam coupled to 2.5 inch widened aftermarket
linkpin arms in order to gain more front end wheel travel ( mainly downwards travel ) and still keep the front end and tyres under a widened cheetah
fender front end ? Any ideas or oppinions would be great
Love is a Rotary baja bug
Just be carefull  ,, something dangerous is lurkin in My garage
ready to burst out in a fit of Big Hp, high boost baja Rage .
http://groups.msn.com/GottaVW |
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on August 16th, 2012 at 09:49 PM |
|
|
Widened arms aren't going to give you any more travel then standard arms. If you want more travel you need to go to longer front trailing arms.
If you want to run longer front trailing arms you are going to have to move your beam forward too. This usually means cutting the framhead off and
extending it so the beam sits further forward by the same length that your new trailing arms are.
If you run longer trailing arms with the beam in the standard location it'll push your wheels back towards the A pillars and the tyres are going to
rub. Unless you're running really small tyres which I certainly hope you aren't on a Baja 
If the arms are 2.5 inchs wider each you will have to narrow the beam 5 inches not 2.5 inches. Because you have two arms.
Hope this helps mate.
Smiley 
If you said I was a Volkswagen man, you'd be right.
|
|
|
THUDKNUCKLE
A.k.a.: James Stoodley
Officially Full-On Dubber
Posts: 224
Threads: 25
Registered: April 19th, 2005
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Crazy
|
| posted on August 17th, 2012 at 09:19 AM |
|
|
Thanks that was an awsome answer
Love is a Rotary baja bug
Just be carefull ,, something dangerous is lurkin in My garage
ready to burst out in a fit of Big Hp, high boost baja Rage .
http://groups.msn.com/GottaVW |
|
|
nils
Fahrvergnugen
Posts: 971
Threads: 65
Registered: January 11th, 2008
Member Is Offline
Location: central coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on August 17th, 2012 at 12:01 PM |
|
|
Actually smiley, wider will give you a bit more, but not if you narrow the beam. because the limiting factor is the steering arms hitting the chassis
or the tierod ball joints. on there angle downwards, if they are wider the outside balljoint ends up lower. but not much.
If you want to stay under the gaurds. you'll get a better result by sectioning the frame head or going rack and pinion. there are heaps of mods
that you can do to the stand beam/arms to get more travel, the 1600 class bajas in the statea are getting 10-12 inchs with standard arms, which is
double standard
my front has ALOT going on, including 2.5' longer arms and have a conservative 14inches at the moment
Quit calling rust patina
|
|
|
Smiley
A.k.a.: Daniel Stephens
Veteran Volks Folk
Posts: 2125
Threads: 110
Registered: October 29th, 2008
Member Is Offline
Location: Yeppoon, Central Queensland
Theme: UltimaBB Pro Blue
Mood: Synchro'd
|
| posted on August 19th, 2012 at 05:49 PM |
|
|
Thanks for fixing my mistakes Nils. I see you're on here a bit more lately, thanks good so I can drool over your Baja some more.
I'm looking at getting more out of my frontend too, but can't do anything till I fit my rack. It's amazing the race guys are getting so much travel
with stock arms, gives me something to aim for
Smiley
If you said I was a Volkswagen man, you'd be right.
|
|
|
