[ Total Views: 1132 | Total Replies: 20 | Thread Id: 99431 ] |
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
posted on October 28th, 2012 at 09:38 PM |
|
|
HPMX V Weber
http://www.youtube.com/watch?v=WP3fOWaaQy4&feature=related
Worth watching.
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
posted on October 29th, 2012 at 12:07 AM |
|
|
Um, yet right at the start they say that they have profiled the throttle shaft and increased the bore diameter to increase gas flow thro the HMPX.
Therefore not a straight out of the box comparison.
If you knife edge the throttle butterflies, flow the throttle spindles and smooth the venturi's then any carb will flow better than it's out the box
cousin.
Also, unless actually cast in America then the EMPI brand still suffer from poor Chinese manufacturing porosity and strength.
madness is in the eye of the beholder
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
posted on October 29th, 2012 at 05:46 AM |
|
|
It is a direct out of the box comparison, these feature's are standard on the HPMX as they state that these improvment's have been made as part of
there manufacturing process.
|
|
steve burgess
Slammed & Awesome Dubber
Posts: 92
Threads: 10
Registered: May 21st, 2011
Member Is Offline
Location: nambour
Theme: UltimaBB Vintage
|
posted on October 29th, 2012 at 08:31 AM |
|
|
Iam running a set of cheap chinese 40 idf. went through them before fitting and all was good.They are running great so no complaints from me. Saved
many $$
I think the early ones were bad so would be careful buying second hand.
1956 judson supercharged oval
1975 kombi camper
1976 kombi panel van
|
|
snitz
Wolfsburg Wizard
Posts: 605
Threads: 37
Registered: September 28th, 2008
Member Is Offline
Location: Adelaide.. the defect and taser state..
Theme: UltimaBB Psyche Red
Mood: "Bug"gered
|
posted on October 29th, 2012 at 10:41 AM |
|
|
Wifes 1916cc '70 beetle runs 40mm HPMXs..Runs really well but a little too rich on the idle jets.Despite this its quite economical..well compared to
my twin turbo Legnum..lol.
Once run in its on a mates dyno to re-jet and check mixtures.Ive sold 5 pairs of 36idfs (3 sets on this forum alone) and honestly the quality is right
up there in terms of the carbies..I think the hex bar linkage set up is of a lower quality than others but still performs well.
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
posted on October 29th, 2012 at 12:11 PM |
|
|
Quote: | Originally
posted by vwo60
It is a direct out of the box comparison, these feature's are standard on the HPMX as they state that these improvment's have been made as part of
there manufacturing process.
|
Hmm, well I'd be interested to see how the Weber's would stack up against the Empi's with the same improvements made. That IMO would be a fairer
comparison.
Still if the Empi's don't have any quality issues then they look like a good buy
madness is in the eye of the beholder
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
posted on October 29th, 2012 at 02:14 PM |
|
|
I've had troubles with manufacturing issues with the HPMX's so I won't be recommending them, but that aside, it is interesting to note, the AFR's
are different on both engines in the comparisons. This is because for whatever reason the HPMX wants a slightly richer set-up than an IDF, and the
dyno sheets back this, therefore for a power comparison, surely the jetting should first be set for what the engine/carb combo requires before maximum
output is tested. Then it would be a performance comparison. Anyway, I use and recommend Weber as driveability and longevety does not show up on a
dyno pull.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
posted on October 29th, 2012 at 02:27 PM |
|
|
if its on youtube.....well then it must be true
|
|
Klaus
Custom Title Time!
Posts: 1439
Threads: 100
Registered: August 25th, 2004
Member Is Offline
Location: Wollongong
Theme: UltimaBB Pro Blue ( Default )
Mood: Heavily modified
|
posted on October 29th, 2012 at 04:38 PM |
|
|
nice to see they mentioned the fact you have to empty float bowls of swarf and set the float levels on the hpmx's ..ha
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
posted on October 29th, 2012 at 06:56 PM |
|
|
I think you are missing the point psimatar, there are both out of the box, weber would have to make the changes in the manufacturing process to the
IDF's that the HMPX have standard.
|
|
coletrickle
Wolfsburg Wizard
Posts: 661
Threads: 34
Registered: April 22nd, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
posted on October 29th, 2012 at 08:04 PM |
|
|
Are the hpmx throttle blades the same diameter as the webbers that they copied?
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
posted on October 29th, 2012 at 08:13 PM |
|
|
Quote: | Originally
posted by coletrickle
Are the hpmx throttle blades the same diameter as the webbers that they copied?
| Yes
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
coletrickle
Wolfsburg Wizard
Posts: 661
Threads: 34
Registered: April 22nd, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
posted on October 29th, 2012 at 08:20 PM |
|
|
Thanks matty,I'll reserve my decision on the hpmx's for say 20 years!
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
posted on October 29th, 2012 at 09:05 PM |
|
|
Quote: | Originally
posted by vwo60
I think you are missing the point psimatar, there are both out of the box, weber would have to make the changes in the manufacturing process to the
IDF's that the HMPX have standard.
|
Not really, they may be modified by the manufacturer after the casting process but as it's been internally massaged then it automatically has an edge
over the Webers if all other dimensions are identical.
So it's like comparing an OEM cylinder head and a JPM cylinder head. Both 'straight out the box' but ones been played with so not the same.
I used to be able to modify the Weber DGAV on Ford pinto's to flow close to a pair of DCOE's for fuelling restricted race engines.
I'm just saying that if the Weber had the same manufacturers modifications done to them then that would be a more interesting comparison.
madness is in the eye of the beholder
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
posted on October 29th, 2012 at 09:20 PM |
|
|
the youtube test is done by an Empi supporting person/company.........do you really think its going to be unbiased ???
Notice they dyno run the HPMX first......maybe its because after a few runs they know HP will drop off due to heat sink.
I bet if they pulled 10 sets of HPMX carbs out of boxes and tested them they would ALL have a different result......the same if they did it with
webers
The only real comparison would be to tune the carbs to match the motor and then see which one produces the best result.
|
|
colin
Fahrvergnugen
Posts: 984
Threads: 82
Registered: March 7th, 2007
Member Is Offline
Location: Tamworth
Theme: UltimaBB Pro Blue ( Default )
|
posted on October 31st, 2012 at 07:14 PM |
|
|
Quote: | Originally
posted by matberry
I've had troubles with manufacturing issues with the HPMX's so I won't be recommending them, but that aside, it is interesting to note, the AFR's
are different on both engines in the comparisons. This is because for whatever reason the HPMX wants a slightly richer set-up than an IDF, and the
dyno sheets back this, therefore for a power comparison, surely the jetting should first be set for what the engine/carb combo requires before maximum
output is tested. Then it would be a performance comparison. Anyway, I use and recommend Weber as driveability and longevety does not show up on a
dyno pull.
|
Very wise words Matt,
Each carb brand must be jetted individually for a true comparision.
Cheers Col
|
|
tar76
Custom Title Time!
Posts: 1622
Threads: 95
Registered: December 18th, 2009
Member Is Offline
Location: Ningi Qld
Theme: UltimaBB Pro Blue
Mood: Rollin with The Dub Collective
|
posted on October 31st, 2012 at 07:30 PM |
|
|
Had a set of HPMX on my old panel and could never get them to idle right. they use to always play up if you let it sit and idle for too long, had to
keep pumping the throttle every 30 seconds. that was my main bug bare with them use to really shit me at the lights.
"Obey your Dreams"!
62 Std beetle.
65 11 wnd Split "The Cross".
6? coming very soon!!!!
|
|
70AutoStik
Insano Dub Head
Posts: 730
Threads: 18
Registered: August 30th, 2002
Member Is Offline
Location: Dandenong. Victoria
Theme: UltimaBB Pro Blue ( Default )
|
posted on November 5th, 2012 at 05:26 PM |
|
|
Hehehe, we tend to expect mindless racial prejudice from Americans, but over on thesamba the consensus seems to be the HPMX are looking good. The
Spanish Webers have been getting worse and worse - so bad people are considering Kadrons...
I picked up a pair of their ICT copies as I needed something to get an engine running and it was actually cheaper than picking up a good used or stock
carb here! I was actually shocked at the quality - I remember Empi as shipping crap that you wouldn't even want to hang on your wall.
So, I'm afraid I tend to agree with the Americans, the new Empi carbs are well worth a look. Ask a few people who aren't selling them what they
thought of recent Weber offerings... Sad but true.
|
|
tar76
Custom Title Time!
Posts: 1622
Threads: 95
Registered: December 18th, 2009
Member Is Offline
Location: Ningi Qld
Theme: UltimaBB Pro Blue
Mood: Rollin with The Dub Collective
|
posted on November 5th, 2012 at 05:49 PM |
|
|
Mine were the first model type but have heard the next gen were made better?
They wouldn't stack up to Dells!!
"Obey your Dreams"!
62 Std beetle.
65 11 wnd Split "The Cross".
6? coming very soon!!!!
|
|
OZ Towdster
A.k.a.: Andrew Westwood
Custom Title Time!
Keen to finish some projects
Posts: 1921
Threads: 132
Registered: December 7th, 2003
Member Is Offline
Location: Alexandra Hills Brisbane QLD
Theme: UltimaBB Pro Yellow
Mood: Having fun in our great land
|
posted on November 5th, 2012 at 06:01 PM |
|
|
Tarin , Dells are / were a great carby , right up to the point of trying to buy parts for them now , part of the reason i dropped the drla for the
kaddies
Don't let body work get in the way of real suspension travel
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
posted on November 5th, 2012 at 06:45 PM |
|
|
I run 48 drla's and have had no problems getting anything i needed, all has been available, from the uk or us, as for going back to kadron, what a
disapointment that would be.
|
|