| [ Total Views: 1443 | Total Replies: 36 | Thread Id: 51977 ] |
| Pages: 1 2 |
|
|
 Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
| posted on May 11th, 2006 at 04:35 PM |
|
|
| Quote: | Originally
posted by Bizarre
Does the line bore include for thrust cutting #1???
|
Yes if required, all included for $99. No need to machine the bearing, Stan will machine the case to suit 'off the shelf' bearings. e.g. 1mm, 2mm
thrustcut.
Does that answer your question?
|
|
|
 Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12778
Threads: 734
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 11th, 2006 at 05:42 PM |
|
|
| Quote: | Originally
posted by Craig Torrens
Does that answer your question?
|
For the moment.
I am sure i will think of some thing later to ask.
:jesus
Futue te ipsum!!!
|
|
|
Bizarre
Super Moderator
The artist formerly known as blue74l
Posts: 12778
Threads: 734
Registered: August 25th, 2002
Member Is Offline
Location: Abbotsford, Sydney
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 11th, 2006 at 05:42 PM |
|
|
Futue te ipsum!!!
|
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
| posted on May 11th, 2006 at 06:04 PM |
|
|
Love your work Baz !
|
|
|
Craig Torrens
A.k.a.: Craig Torrens
Scirocco Rare
6 times Australian, 7 times State Hillclimb Class Champion
Posts: 8040
Threads: 347
Registered: January 10th, 2003
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Time to go Salt lake racing, and actually achieve a result.
|
| posted on May 11th, 2006 at 06:05 PM |
|
|
| Quote: | Originally
posted by bajaben
yeah but he is an expert and this guy is a normal engineer and i live like about 2000km away haha
[ Edited on 10/5/2006 by bajaben ]
|
Australia post.............its cheaper than you think.
|
|
|
bajaben
A.k.a.: Ben Alderson
Officially Full-On Dubber
Posts: 222
Threads: 33
Registered: May 10th, 2005
Member Is Offline
Location: Townsville, north queensland
Theme: UltimaBB Pro Blue ( Default )
Mood: need more power
|
| posted on May 12th, 2006 at 04:55 PM |
|
|
well its too late for me now, its already in the shop. oh well. get the case and heads back next week, give the heads a clean up and get them looked
at then it will be time to start putting it together. what compression ratio should i run? im thinking of going for the supercharged route later on
down the track so i think keeping it low for now would be good. then again its not hard to lower it once needed. any suggestions?
trunk monkey, because sometime getting your car back just isn't enough
|
|
|
lugnuts
A.k.a.: Mike
Custom Title Time!
Posts: 1070
Threads: 88
Registered: August 28th, 2002
Member Is Offline
Location: Sydney,Castle Hill
Theme: UltimaBB Pro Blue ( Default )
Mood: semi-retiring
|
| posted on May 16th, 2006 at 02:54 AM |
|
|
| Quote: | Originally
posted by bajaben. the case halves are being machined to fit together better
|
:duh
Dont listen to what they say,just watch what they do.Oh yeah ive NEVER finished anything ive started.:o
|
|
|
| Pages: 1 2 |
