[ Total Views: 962 | Total Replies: 2 | Thread Id: 1011 ] |
|
VWFOOL
Bishop of Volkswagenism
King for a day, Fool for a lifetime.
Posts: 3436
Threads: 572
Registered: September 3rd, 2002
Member Is Offline
Location: Newcastle - Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: inspired yet?
|
posted on October 5th, 2002 at 10:12 PM |
|
|
plz explain dropped spindles to me.
i have an adjustable front beam that i have lowered.
can you tell me what dropped spindles do and whether i need them on my beetle?
how much are they?
thanks for ur help:thumb
++++++++++++++++++++++++++++
One man's junk...
|
|
KruizinKombi
A.k.a.: Col
Bishop of Volkswagenism
Seriously Obsessed Cyber Dubber
Posts: 3493
Threads: 104
Registered: August 25th, 2002
Member Is Offline
Location: Gippsland, Victoria
Theme: UltimaBB Pro Blue ( Default )
Mood: Indifferent
|
posted on October 5th, 2002 at 09:39 PM |
|
|
Hmmm, hard to explain....
Dropped spindles lower the kinpins or balljoints in relation to the axle line. They are more desirable than an adjustable front beam because they
maintain the factory amount of wheel travel and geometry. There are potential problems when dropped spindles are of the cut-and-welded variety,
because the welding changes the tensile strength of the metal (its ability to bend and spring back to shape under stress without cracking). Cast
reproductions can also have problems depending on the quality of the material and cast-work. VW were very good at this.
The third alternative (the one I believe Rob King uses on his lowered Type 2 spindles) is to swap the spindles right-for-left and mount them upside
down which requires the tie-rod end holes to be reamed and tapered the opposite way, and a larger tie-rod end fitted to suit the larger hole. These
have the advantage of using the factory cast units which I think may negate the need for any engineering certificates, but I'm no expert on the
law.
I have no idea what they're worth, try checking the advertisements in Hot VWs or some other american VW magazine.
Kruizin Kol
|
|
vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
posted on October 6th, 2002 at 06:35 AM |
|
|
Col n Sam
I hate dropped spindles.... most of them have been manufactured in 3rd world contries and how could you
trust the forgings, or most of them are probally cast.
I would and do prefer the lowered front end method by cutting and welding it yourself.
|
|
shiftyvw
Wolfsburg Wizard
Posts: 523
Threads: 44
Registered: September 11th, 2002
Member Is Offline
Location: Seven Hills NSW
Theme: UltimaBB Pro Blue ( Default )
|
posted on October 6th, 2002 at 03:12 PM |
|
|
I put cb performance drop spindles on after using an adjustable beam for about a year and personally I think they are excellent. I have to drive my
car everyday and the bumpy ride just became a pain in the ass. I dont brace myself when I see a bump any more. Two things to consider though are the
clearance between the lower ball joint and the rim, I dont think a 14 inch rim would be possible and of course the width factor but with the cb's
this wasnt really a factor. I can understand vw54's concern but I would like to know why ben durie thinks they are crap? as for swapping spindles
side to side I would hate to imagine what this would do to steeing geometry namely SAI.
just my 2 cents. |
|
Zenjoe
Casual Dubber
Posts: 26
Threads: 5
Registered: October 8th, 2002
Member Is Offline
Location: California, USA
Theme: UltimaBB Pro Blue ( Default )
|
posted on October 10th, 2002 at 03:42 AM |
|
|
ShiftyVW is right
www.cbperformance.com offers new forged drop spidles (not welded) and they are
excellenct quality. They increase the track by 1/4 inch per side and geatly improve the ride of your car.
I have a dropped beam that is slammed to the ground. If you look at the trailing arm geometry when you are lowered, you will notice that when the
spindle moves up it will move forward as well. This is what causes lowered VWs to ride like crap. The wheel when hitting a bump, wants to move up and
back, not forward. Stock suspension geometry lets the wheel move up and back, thats what you want for a good ride.
Drop spindles lower the car without changing the suspension arm geometry. Therefor the ride is close to stock.
Another bonus, when lowering a car with the beam only, the tie rods get really angled, which leads to bump steer and irradic steering response, again
fixed by going with dropped spindles.
One condition with the dropped spindles, you need at leat a 15inch rim to use them. If you have a ball joint car, you might need to even trim the
inside of the wheel (if you are using an aluminum wheel)
Hope this helps.
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
posted on October 10th, 2002 at 11:33 PM |
|
|
Good Quality Dropped Spindles are Also Very Expensive..... I believe in the UK, they are available in different sizes of drop!!
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|