| [ Total Views: 565 | Total Replies: 6 | Thread Id: 104133 ] |
|
|
 hulbyw
Insano Dub Head
Posts: 804
Threads: 131
Registered: September 28th, 2009
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: I'm OK, RU?
|
| posted on November 20th, 2013 at 02:26 PM |
|
|
HD Berg Valve Springs in Mild 1776?
I am building a mild 1776 with DP heads that have been cleaned up and the manifolds matched. Carb will be a 40DCN Weber, lightened flywheel and
Vintage Speed exhaust.
Cam is a Wade 149 (regrind). I will be using 1.25 ratio rockers.
Question is should I use HD Berg valve springs (125lbs at 1.5" and 225lbs at 1") or stick with stock vale springs (126lbs at 1.22")? Any help
appreciated!
Cheers..........Wayne
|
|
|
modnrod
Fahrvergnugen
Posts: 978
Threads: 50
Registered: March 17th, 2011
Member Is Offline
Location: Midwest, Westoz.
Theme: UltimaBB Pro Blue
Mood: Old School Volksies!
|
| posted on November 20th, 2013 at 04:22 PM |
|
|
Gday.
I looked through my Wade cams list and can't find that grind number, obviously they have WAY more than on my old list though!
What are the specs on that grind?
|
|
|
hulbyw
Insano Dub Head
Posts: 804
Threads: 131
Registered: September 28th, 2009
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: I'm OK, RU?
|
| posted on November 20th, 2013 at 07:07 PM |
|
|
Not sure on the specs but it is a very mild grind based on a Porsche 90 cam as I undersstand. I had the cam ground years ago and cannot find the specs
|
|
|
modnrod
Fahrvergnugen
Posts: 978
Threads: 50
Registered: March 17th, 2011
Member Is Offline
Location: Midwest, Westoz.
Theme: UltimaBB Pro Blue
Mood: Old School Volksies!
|
| posted on November 20th, 2013 at 07:36 PM |
|
|
I can list what I was going to use in my motor if you like ( it WILL happen eventually....... ), maybe others with more experience than me can go from there perhaps, but it will give you a starting point to
consider.
My cam has 270* advertised, 234*@.050", .330" on the intake lobe, used with 1.4 rockers to yank the valves up to give .462" lift off the seat.
Valves/collets/retainers will be quite a bit lighter than stock (parts not even ordered yet though!) and lighter CB lifters too. I'll be using approx
120lbs on the seat and 215lbs over the nose to go up to the planned 5500rpm limiter.
It would seem to me that your Berg HD singles would be fine, but as I said, others with better knowledge (Mat Berry, Rod Penrose, etc) are a phone
call away to double check.
|
|
|
BiX
Veteran Volks Folk
Posts: 2499
Threads: 154
Registered: September 2nd, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on November 21st, 2013 at 10:13 AM |
|
|
I had a similar engine (1776, W100, dual Dels) and needed HD single valve springs. Its more about how hard you want to rev it.
I have no sympathy for my car, only the wallet that pays for it!
Go hard or go home!!!!
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on November 21st, 2013 at 11:18 AM |
|
|
I'd be using the HD too, rate of rpm increase is what does it, and with 1.25 no question. my 2c
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
hulbyw
Insano Dub Head
Posts: 804
Threads: 131
Registered: September 28th, 2009
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: I'm OK, RU?
|
| posted on November 21st, 2013 at 05:05 PM |
|
|
Thanks guys
|
|
|
