| [ Total Views: 852 | Total Replies: 6 | Thread Id: 104877 ] |
|
|
 Aussie
Officially Full-On Dubber
Posts: 296
Threads: 43
Registered: September 15th, 2006
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 27th, 2014 at 08:35 PM |
|
|
Match Porting Inlet Manifolds
Does anyone have any useful links to a 'How to' article or similiar for match porting manifolds?
Where can I get some of the blue dye to guide the process?
Should the inlet manifold exactly match the head ports or be slightly smaller?
Does anyone sleeve their manifolds to ensure head ports and manifold ports always align properly? Maybe a dowel?
Do people go as far as measuring volume of manifold ports (after the porting process) to make sure that all are equal?
|
|
|
cb john
Wolfsburg Wizard
Posts: 470
Threads: 6
Registered: June 22nd, 2007
Member Is Offline
Location: Sydney
Theme: UltimaBB Pro Blue
|
| posted on January 27th, 2014 at 10:07 PM |
|
|
| Quote: | Originally
posted by Aussie
Does anyone sleeve their manifolds to ensure head ports and manifold ports always align properly? Maybe a dowel?
|
Sleeving is what I do...
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on January 28th, 2014 at 09:11 AM |
|
|
yes
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
dangerous
A.k.a.: Dave Butler Muffin Man
23 Windows of Awesome
Posts: 5901
Threads: 178
Registered: January 6th, 2005
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
Mood: 591
|
| posted on January 28th, 2014 at 10:49 AM |
|
|
http://forums.aussieveedubbers.com/viewtopic.php?tid=27021
If you plan to do just one set of Heads Ian, just use a texta like Niko to mark out the flanges.
I prefer to use a dowel on the intake stud, (two nuts locked on the stud and turned to size),
and this way, you can make the port exactly the same size on both,
with the confidence that they will match time after time.
I like to bolt the assembly together and use a long shanked burr from the chamber side.
(assuming you are using tall manifolds?)
Some projects require cutting the manifold off and re-welding after you have your cross section complete.
If you choose not to make a precise fit,
as the CB stuff arrives,
you will need a smaller port in the manifold so you never get an obstruction.
To me the size of the port becomes a waste of time in that case,
especially if you have an over sized 44 valve in the first place.
Ideally the port should taper in size from the seat throat up to the carb flange.
At the very least, the cross section at the head flange should be the smallest part of the manifold.
No need to measure port volume,
just measure your work with inside calipers,
or a suitably made template.
Card board or tin, is good on a threaded stud.
| Quote: | Originally
posted by westi
That's mad Alan.
|
|
|
|
Aussie
Officially Full-On Dubber
Posts: 296
Threads: 43
Registered: September 15th, 2006
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on January 28th, 2014 at 07:45 PM |
|
|
| Quote: | Originally
posted by dangerous
http://forums.aussieveedubbers.com/viewtopic.php?tid=27021
I prefer to use a dowel on the intake stud, (two nuts locked on the stud and turned to size),
and this way, you can make the port exactly the same size on both,
with the confidence that they will match time after time.
|
Thanks Dave. Just to clarify - you effectively sleeve the manifold studs on the head using a couple of nuts machined down to be a tight fit with the
manifold mount holes?
|
|
|
psimitar
Son of Jim - Creator of Good
Posts: 2506
Threads: 148
Registered: January 1st, 2009
Member Is Offline
Location: North East Melbourne, VIC
Theme: UltimaBB Psyche Blue
|
| posted on January 28th, 2014 at 09:22 PM |
|
|
I've always used a shanked stud and then made sure the manifold stud holes are a snug fit over the central shanked area of the stud. same as sleeving
but I prefer using shanked studs instead of fully threaded. The fully threaded just don't locate as nicely as the shanked studs.
here ya go for some fairly cheap engineers blue EBay Engineers blue
madness is in the eye of the beholder  |
|
|
dangerous
A.k.a.: Dave Butler Muffin Man
23 Windows of Awesome
Posts: 5901
Threads: 178
Registered: January 6th, 2005
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Blue ( Default )
Mood: 591
|
| posted on January 29th, 2014 at 05:50 AM |
|
|
| Quote: | Originally
posted by Aussie
| Quote: | Originally
posted by dangerous
http://forums.aussieveedubbers.com/viewtopic.php?tid=27021
I prefer to use a dowel on the intake stud, (two nuts locked on the stud and turned to size),
and this way, you can make the port exactly the same size on both,
with the confidence that they will match time after time.
|
Thanks Dave. Just to clarify - you effectively sleeve the manifold studs on the head using a couple of nuts machined down to be a tight fit with the
manifold mount holes?
|
Yes Ian.
It effectively becomes a "shanked stud" as psimitar would say,
but is larger in diameter than anything off-the-shelf,
because the holes are mostly so large.
P.S. always Loctite the two nuts before they are machined to size.
| Quote: | Originally
posted by westi
That's mad Alan.
|
|
|
|
