| [ Total Views: 2139 | Total Replies: 4 | Thread Id: 110866 ] |
|
|
 Lolita
Learner Dubber
Posts: 2
Threads: 1
Registered: April 24th, 2016
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 24th, 2016 at 11:02 AM |
|
|
Lower Sliding Door Track Replacement Hell - Sydney
Hey guys.
We have put our 1976 kombi T2 in the shop to get the lower sliding door track replaced, and long story short the job came back with a door that
doesn't close properly (from a badly manufactured tp sill/track) and a weld join at the rear. We have already taken it back to the shop as the first
time we got it back, it would hardly open all the way because of the weld.
What are our options?
We would like to find a proper precise body shop near Sydney who could fix this hell. Any recomendations?
(The details: We provided the parts except the top sill/track bit which had to be manufactured. It looks like they did not replace the full length,
leaving a join at the rear about 30cms in from the end. The manufactured top sill with the track was done very roughly, so when you go to close the
door, it is about an inch too far out. You have to push the door in at the bottom and then close it. They have bent the track in and out along the
full length to make it fit, so realistically, this top track/sill would have to be re-manufactured properly and put in again if we want it to last
more than a year. The overall quality is very sloppy with loose unwelded sections, bent everywhere, holes from welding, etc. The paint on the door
has been messed up with some chemicals, the bumper bar was snapped off while in the shop and the welds are really rough and the paint hasn't been
fixed. So we are not in a hurry to take it back to this guy a third time.)
Any helpful advise would be appreciated.
Cheers |
|
|
grumble
Son of Jim - Creator of Good
Posts: 2668
Threads: 53
Registered: June 10th, 2008
Member Is Offline
Location: Taree
Theme: UltimaBB Pro Blue ( Default )
Mood: happy all the time
|
| posted on April 24th, 2016 at 04:47 PM |
|
|
That is what the Motor Vehicle Repair Industry Council was for,I believe it has now been integrated into the Department of fair Trading,check the Govt
entries in the phone book and ask them for advice on how to proceed with a claim against the repairer.
|
|
|
Lolita
Learner Dubber
Posts: 2
Threads: 1
Registered: April 24th, 2016
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 26th, 2016 at 09:08 AM |
|
|
Ok thanks.
We have lodges forms to the Department of fair Trading.
And we'll try to take it to either Indian Automotive, Wayne Penrose or EastCoast Kombis to get this sorted.
Cheers |
|
|
kylandpl
Casual Dubber
Posts: 24
Threads: 5
Registered: December 30th, 2008
Member Is Offline
Location: Central Coast, NSW
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 4th, 2016 at 10:00 PM |
|
|
+1 for Paul at East Coast Kombis. Did rust repair on my Beetle, very happy.
|
|
|
johnharte
Casual Dubber
Posts: 26
Threads: 9
Registered: May 7th, 2010
Member Is Offline
Location: Kurrajong - Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Chilled
|
| posted on November 6th, 2016 at 12:28 PM |
|
|
Old thread I Know....
But how did you get on?
+1 for Mikki at Indian Automotive........ have a look at my Lowlight thread, the guys there are magicians
|
|
|
