| [ Total Views: 1246 | Total Replies: 6 | Thread Id: 113853 ] |
|
|
 hulbyw
Insano Dub Head
Posts: 804
Threads: 131
Registered: September 28th, 2009
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: I'm OK, RU?
|
| posted on September 26th, 2020 at 09:21 PM |
|
|
1968 Beetle Engine Bay
Can anyone tell me if the 1968 Beetle engine bay tapers in towards the rear of the car or are the sides (where the engine seal fits) parallel?
Cheers.............Wayne
|
|
|
bushed
Wolfsburg Elder
Posts: 3539
Threads: 66
Registered: December 18th, 2006
Member Is Offline
Location: Lowood Qld
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 27th, 2020 at 12:56 PM |
|
|
parallel like the engine shape, Wayne, b.
want any vw bits old but like me, Made in Germany!!!
|
|
|
hulbyw
Insano Dub Head
Posts: 804
Threads: 131
Registered: September 28th, 2009
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: I'm OK, RU?
|
| posted on September 27th, 2020 at 05:23 PM |
|
|
Excellent. That means I got it right when I used a scissor jack to make the engine seal mounting flanges parallel (moved them out around 30mm!)
Cheers
|
|
|
 vw54
Super Administrator
Always Waiting 4 Friday
Posts: 16723
Threads: 378
Registered: August 26th, 2002
Member Is Offline
Location: Sunny Sydney
Theme: UltimaBB Pro Blue ( Default )
Mood: Oval resto ongoing
|
| posted on September 28th, 2020 at 08:30 AM |
|
|
Are you fitting a bigger capacity engine ???
|
|
|
hulbyw
Insano Dub Head
Posts: 804
Threads: 131
Registered: September 28th, 2009
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: I'm OK, RU?
|
| posted on September 28th, 2020 at 11:14 AM |
|
|
Yes I am, but even with the stock engine, getting the rocker covers off was a challenge and the engine seal had a small gap in the left rear corner.
Reckon my car has had a few whacks both ends early in it's life (prior to my ownership) that were repaired by folks who had little knowledge of VW's
or didn't care.
|
|
|
grumble
Son of Jim - Creator of Good
Posts: 2668
Threads: 53
Registered: June 10th, 2008
Member Is Offline
Location: Taree
Theme: UltimaBB Pro Blue ( Default )
Mood: happy all the time
|
| posted on October 2nd, 2020 at 06:37 PM |
|
|
hulbyvw in the local manufacture of workshop tools there is one for the reshaping of the engine bay.
|
|
|
hulbyw
Insano Dub Head
Posts: 804
Threads: 131
Registered: September 28th, 2009
Member Is Offline
Location: Melbourne
Theme: UltimaBB Pro Blue ( Default )
Mood: I'm OK, RU?
|
| posted on October 4th, 2020 at 12:43 PM |
|
|
Thanks grumble, I didn't think to look at the workshop tools. Tool #701 is the one I think you are referring to. It's dimensions are 733mm wide. My
engine bay now measures 735mm wide after the "jacking" so I am quite happy with that. Thanks again
Cheers
|
|
|
