| [ Total Views: 1200 | Total Replies: 11 | Thread Id: 56221 ] |
|
|
 pete wood
A.k.a.: figure itout
23 Windows of Awesome
Posts: 6828
Threads: 389
Registered: January 15th, 2004
Member Is Offline
Location: Nth Nth StMarys, Sydney
Theme: UltimaBB Pro White
Mood: upgrades = jackstands
|
| posted on September 8th, 2006 at 01:11 PM |
|
|
Anyone had a crank angle sensor go on an EJ subaru?
I think mine's just gone and I was wondering if it was a common occurance?
|
|
|
MickH
A.k.a.: Michael Hutchinson
Bishop of Volkswagenism
Hairy Gutted Sloth
Posts: 3389
Threads: 29
Registered: September 6th, 2003
Member Is Offline
Location: TownsvilleTropical North QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: Grow a brain...walls don't hit back...
|
| posted on September 8th, 2006 at 01:20 PM |
|
|
Mines bolted down....where did it go??? Just kidding. There is nothing to the sensors..have you checked the wiring?? A bad connection would be more
likely. What makes you think it's that sensor and what are the symptoms??
tssnq.com.au
|
|
|
pete wood
A.k.a.: figure itout
23 Windows of Awesome
Posts: 6828
Threads: 389
Registered: January 15th, 2004
Member Is Offline
Location: Nth Nth StMarys, Sydney
Theme: UltimaBB Pro White
Mood: upgrades = jackstands
|
| posted on September 8th, 2006 at 01:41 PM |
|
|
won't run, ECU is throwing a fault code that says the crank angle sensor is the issue. I'm trying to test the wiring now with not much success. At
the mo the continuity tester shows NO connection between the sensor plug and the ECu plug. 
I'm hoping I have the wrong terminals, otherwise I'm gonna have to trace it back through the loom. 
|
|
|
MickH
A.k.a.: Michael Hutchinson
Bishop of Volkswagenism
Hairy Gutted Sloth
Posts: 3389
Threads: 29
Registered: September 6th, 2003
Member Is Offline
Location: TownsvilleTropical North QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: Grow a brain...walls don't hit back...
|
| posted on September 8th, 2006 at 01:47 PM |
|
|
can you bridge the wire from the sensor to the ECU to confirm?? (bypass the loom) Might speed things up a little....if you can it will confirm the
sensor is dead or the wiring is u/s.
tssnq.com.au
|
|
|
pete wood
A.k.a.: figure itout
23 Windows of Awesome
Posts: 6828
Threads: 389
Registered: January 15th, 2004
Member Is Offline
Location: Nth Nth StMarys, Sydney
Theme: UltimaBB Pro White
Mood: upgrades = jackstands
|
| posted on September 8th, 2006 at 02:01 PM |
|
|
yeah maybe, I'll try that. Which is which pole on the sensor, or doesn't it matter?
[ Edited on 8-9-06 by pete wood ]
|
|
|
Kombicol
Officially Full-On Dubber
Posts: 211
Threads: 18
Registered: September 14th, 2003
Member Is Offline
Location: Perth WA - sand it's everywhere!!
Theme: UltimaBB Pro Blue ( Default )
Mood: subariffic
|
| posted on September 8th, 2006 at 02:04 PM |
|
|
Hi,
They are a pretty bullet proof bit of gear, be surprised if it is RS, shouldn't be too hard to trace though. The can and crank sensors are the lot of
3 wires with the grey sheilding which goes pretty well alll the way up to the ECU.
Is it missing/backfiring when u try to start? sure you haven't slipped a timing tooth?
|
|
|
MickH
A.k.a.: Michael Hutchinson
Bishop of Volkswagenism
Hairy Gutted Sloth
Posts: 3389
Threads: 29
Registered: September 6th, 2003
Member Is Offline
Location: TownsvilleTropical North QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: Grow a brain...walls don't hit back...
|
| posted on September 8th, 2006 at 02:12 PM |
|
|
I think you would need to run both wires...you can check with a multimeter to see if the sensor is working if it is a pulse sensor....remove the
sensor and connect your multimeter + and - to the wires from the sensor..the order doesn't matter. You are trying to detect if the sensor is putting
out a voltage which you are about to make by waving a screwdriver past the sensor head quickly ,trying to simulate the movement of the pickup on the
crank. Check to see if a voltage is present..the numbers on the multi should move up and down/fluctuate.You could try this with the sensor still in
the car and by cranking the engine if you want to do it the easy way......but you will need long arms to reach the starter,or a helper. If that checks
out OK dive into the spaghetti and check connectors.
tssnq.com.au
|
|
|
Baja Wes
Bishop of Volkswagenism
V6 Baja Pioneer
Posts: 3119
Threads: 94
Registered: August 26th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Content
|
| posted on September 8th, 2006 at 02:30 PM |
|
|
no idea what the EJ sensor is like, but this document for my V6 may be of some help (possibly);
http://www.offroadvw.net/bajawes/KLZE/reading%20malf%20codes.pdf
If you read down to code 2 you will see it is the crank angle sensor. On my V6 it has 2 of most sensors, so if the crank sensor dies it ignores it and
runs off the sensor in the distributor.
The document does describe things to test, and resistance to measure. This will only help if your sensor is a similar type...
|
|
|
speedster356
A.k.a.: Peter Mcleod
Custom Title Time!
Plastic not Classic Racing
Posts: 1624
Threads: 256
Registered: August 25th, 2002
Member Is Offline
Location: CHRIST church NZ
Theme: UltimaBB Pro Blue ( Default )
Mood: Producing boost again in NZ
|
| posted on September 8th, 2006 at 03:28 PM |
|
|
I've heard of this problem quite a few times on various forums, but all times it's been a fault somewhere else in the system and not the sensor. I
have a spare if you want to confirm.
Spyder-WISD 07-09-05 11.6s @ 125 MPH
Speedster-WISD Nats 05 14.4s @ 89 MPH
Jet cruiser-Coogee 22-09-05 900 deg C @ 110,000 rpm
Weaseling out of things is what separates us from the animals....................Except the Weasel.
|
|
|
pete wood
A.k.a.: figure itout
23 Windows of Awesome
Posts: 6828
Threads: 389
Registered: January 15th, 2004
Member Is Offline
Location: Nth Nth StMarys, Sydney
Theme: UltimaBB Pro White
Mood: upgrades = jackstands
|
| posted on September 8th, 2006 at 06:07 PM |
|
|
Newsflash: the wiring was fine, the sensor was not.
Backyard mechanics: 1,
Subaru: 0.
Just got a 2nd handy, $88
Let yáll know how it goes.
|
|
|
MickH
A.k.a.: Michael Hutchinson
Bishop of Volkswagenism
Hairy Gutted Sloth
Posts: 3389
Threads: 29
Registered: September 6th, 2003
Member Is Offline
Location: TownsvilleTropical North QLD
Theme: UltimaBB Pro Blue ( Default )
Mood: Grow a brain...walls don't hit back...
|
| posted on September 8th, 2006 at 10:03 PM |
|
|
Soooo.......is it fixed yet??
tssnq.com.au
|
|
|
pete wood
A.k.a.: figure itout
23 Windows of Awesome
Posts: 6828
Threads: 389
Registered: January 15th, 2004
Member Is Offline
Location: Nth Nth StMarys, Sydney
Theme: UltimaBB Pro White
Mood: upgrades = jackstands
|
| posted on September 8th, 2006 at 11:36 PM |
|
|
All good, plugged it in, bolted it down and it fired up straight off. Sensor came off an Ej22, just goes to show Ej22s are good for something. 
BTW, thanx for the call today Mick. Now I know why you spend so much time on the forum.
|
|
|
