| [ Total Views: 1021 | Total Replies: 6 | Thread Id: 89863 ] |
|
|
 P4UL
Learner Dubber
Posts: 4
Threads: 1
Registered: September 22nd, 2010
Member Is Offline
Theme: UltimaBB Pro Grey
|
| posted on April 15th, 2011 at 06:37 AM |
|
|
Flywheel bolts
Can anyone tell me the spline type & size needed to undo the flywheel to crank bolts with?
I dont want to buy a whole set just to find the right size etc when 1 will do.
I have a 2001 2ltr n/a Legacy engine.
Ta |
|
|
rocknrob
A.k.a.: Rob
Insano Dub Head
Posts: 844
Threads: 90
Registered: December 18th, 2003
Member Is Offline
Location: Gold Coast
Theme: UltimaBB Pro Black
Mood: mystic
|
| posted on April 15th, 2011 at 09:02 AM |
|
|
just a 14mm socket on mine
|
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 17th, 2011 at 12:26 AM |
|
|
Paul were are you located ?
Looking for that special lady : PM me for coffee & cake
|
|
|
P4UL
Learner Dubber
Posts: 4
Threads: 1
Registered: September 22nd, 2010
Member Is Offline
Theme: UltimaBB Pro Grey
|
| posted on April 18th, 2011 at 05:51 PM |
|
|
Hey Guys,
Im in the UK. I managed to borrow one from a neighbour. Its a TX50 or T50 with 6 points inside if anyone else comes accross this. Flywheel is now off
|
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 20th, 2011 at 12:03 AM |
|
|
correct
Looking for that special lady : PM me for coffee & cake
|
|
|
lou0060
Wolfsburg Wizard
Posts: 568
Threads: 30
Registered: December 12th, 2010
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on April 20th, 2011 at 09:06 PM |
|
|
make sure you use the solid type rather than the security ones with the hole in the middle. These don't take the torque required to get the solid
torx screws off.
1971 karmann ghia Cabrio - Cruising 
1963 beetle Sunroof - gathering dust 
1968 race beetle - twin turbo Subaru - stress relief 
1960 beetle - old school low & slow  |
|
|
P4UL
Learner Dubber
Posts: 4
Threads: 1
Registered: September 22nd, 2010
Member Is Offline
Theme: UltimaBB Pro Grey
|
| posted on April 21st, 2011 at 06:56 AM |
|
|
| Quote: | Originally
posted by lou0060
make sure you use the solid type rather than the security ones with the hole in the middle. These don't take the torque required to get the solid
torx screws off.
|
Good advice!
I wont be re-using them, my conversion flywheel came with a new set of hex head bolts. |
|
|
