| [ Total Views: 748 | Total Replies: 9 | Thread Id: 92598 ] |
|
|
 MWH78
Casual Dubber
Posts: 28
Threads: 9
Registered: November 6th, 2010
Member Is Offline
Location: Ipswich, Queensland
Theme: UltimaBB Pro Charcoal
|
| posted on September 11th, 2011 at 09:11 PM |
|
|
Clutch Tube Install
We have a 70 beetle on 68 semi auto pan and after much umming and ahhing have finally decided to cut the pan and install a clutch tube. I have done
lots of searches and have a pretty good idea how to do it but have a couple of questions. A few places suggested that a heavy walled steel tube be
used so as not to blow through with the welder. Any ideas where to get this tube from (we live in Ipswich), would any steel suppliers stock it or
should we be looking elsewhere?
Most of the how to's I have read mention nothing about a bend in the tube but a couple of photos I have seen appear to have a bend towards the rear
is this the case or can the tube be simply left straight?
Thanks in advance for any help anyone can give us.
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on September 11th, 2011 at 10:35 PM |
|
|
If you use thick wall you may need to machine it down for the bowden tube to fit. I've used std steel tube available at a steel supplier, no probs
with a mig and being carefull. Tube stays straight with a general flex/gradual bend.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on September 12th, 2011 at 10:03 AM |
|
|
Any hydraulic supply shop will have tubing in metric or imperial with varing wall thickness that you can adapt
|
|
|
MWH78
Casual Dubber
Posts: 28
Threads: 9
Registered: November 6th, 2010
Member Is Offline
Location: Ipswich, Queensland
Theme: UltimaBB Pro Charcoal
|
| posted on September 12th, 2011 at 05:11 PM |
|
|
Cool thanks for that info. In most of the sites I have seen about doing this cut the front of the tunnel on the right hand side but these are for
left hand drive cars, would this be the same for a right hand drive car or should the cut be made on the passenger side?
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on September 12th, 2011 at 05:18 PM |
|
|
Hi
A thought while you have the pan open, I ran tube big enough to feed a bowden cable through for the accelerator, works beautifully, much better than
running the accelerator cable through the stock steel tube.
Steve
|
|
|
MWH78
Casual Dubber
Posts: 28
Threads: 9
Registered: November 6th, 2010
Member Is Offline
Location: Ipswich, Queensland
Theme: UltimaBB Pro Charcoal
|
| posted on September 12th, 2011 at 07:39 PM |
|
|
Sorry if this is a silly question but would that mean running 2 clutch bowden tubes side by side? Would you use a second bowden tube bracket (not sure
of its propper name) if so where did you mount it? Do you have a pic of your setup, I would be interested to see how you did it?
|
|
|
matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on September 12th, 2011 at 07:40 PM |
|
|
Clutch tube is the same left or right hand drive.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
|
|
|
MWH78
Casual Dubber
Posts: 28
Threads: 9
Registered: November 6th, 2010
Member Is Offline
Location: Ipswich, Queensland
Theme: UltimaBB Pro Charcoal
|
| posted on September 12th, 2011 at 08:06 PM |
|
|
I thought that might be the case, just wanted to check and make sure.
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on September 12th, 2011 at 08:36 PM |
|
|
| Quote: | Originally
posted by MWH78
Sorry if this is a silly question but would that mean running 2 clutch bowden tubes side by side? Would you use a second bowden tube bracket (not sure
of its propper name) if so where did you mount it? Do you have a pic of your setup, I would be interested to see how you did it?
|
Hi
Yes it would mean running another tube, not a bige once you are in there, I just made the hole bigger where the stock tube comes out of the chassis
each end, no photos sorry. I just had to be careful when I was welding it in place that I didn't encroach on the inside of the tube.
Steve
|
|
|
clinker42
Officially Full-On Dubber
Posts: 381
Threads: 154
Registered: August 19th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on September 13th, 2011 at 07:46 PM |
|
|
I think Matts correct, as you go thicker in the wall, the outside dia stays the same but the inner reduces.
Dont worry about thick wall, you can weld thin if you turn the wire speed and amps down. If you only have a stick then just get some 2mm rods.
Birdshit still holds lol
|
|
|
