| [ Total Views: 495 | Total Replies: 3 | Thread Id: 94464 ] |
|
|
 abba
Slammed & Awesome Dubber
Posts: 75
Threads: 23
Registered: June 17th, 2009
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 24th, 2011 at 01:45 AM |
|
|
Ignition/fuel/engine problem
Hi Guys
Need some advice
I have just noticed after taking my Buggy out for a drive that only one side of the engine gets hot . #3, #4 side. I have a dual exhaust set up and
only the one on the #3,#4 side gets hot as well. This side also sounds a little louder and is more consistent in rhythm. The other side sounds more
irregular and pops under deceleration sometimes. The performance seems normal and drove ok. If I didnt notice the cold exhaust I wouldnt have thought
there was a problem. Just worried that there is internal damage. I have a 1916 with dual Kads. I tried different spark plugs and leads. checked fuel
was going to both carbs. All good. I thought maybe a blocked jet so I took the air cleaner off the cold side dripped extra fuel in the carb and it
back fired. Any thoughts ??
|
|
|
jamiesc
Wolfsburg Wizard
Posts: 559
Threads: 106
Registered: December 30th, 2010
Member Is Offline
Location: bayside brisbane
Theme: UltimaBB Pica Red
|
| posted on December 24th, 2011 at 05:22 AM |
|
|
did it backfire befor it happened? the popping on deceleration could be your muffler flange there only like $12 ive had the same problem with my 1800
tp
With your performance not being normal do it feel like the engine is overloading it self like when you get to the certain revs when it gets up and
goes it doesnt feel like it wants to this could be cause from the tappets being too tight
hope this help and merry Christmas
cheers jamie
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on December 24th, 2011 at 06:49 AM |
|
|
odd one that..??
Your 1 & 2 cylinders and heads colder than then 3&4 ??
have You checked the tappets?? on 3 & 4?
either leaking [too tight] or hardly opening [too loose]
Lee
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
abba
Slammed & Awesome Dubber
Posts: 75
Threads: 23
Registered: June 17th, 2009
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
|
| posted on December 24th, 2011 at 11:45 AM |
|
|
| Quote: | Originally
posted by 68AutoBug
odd one that..??
Your 1 & 2 cylinders and heads colder than then 3&4 ??
have You checked the tappets?? on 3 & 4?
either leaking [too tight] or hardly opening [too loose]
Lee
|
Ok will check both sides. When I say colder I mean I can hold the exhaust pipe after 5 min of running. And the air coming out is warm at best. There
is little radiant heat when I touch tappet cover. I dont think any fuel is igniting on that side to cause any heat. will the tappet adjustment correct
this ? I spose we will see. Thanks for the advise guys.
|
|
|
