| [ Total Views: 695 | Total Replies: 6 | Thread Id: 95939 ] |
|
|
 karmad
Casual Dubber
Posts: 30
Threads: 11
Registered: June 10th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 20th, 2012 at 08:05 PM |
|
|
TORSION BAR PROBLEMS
 Hi lads hope someone here can help me.I lowered the back of my 1303
by one outer spline on one side and proceeded to do the other side .I got the spring plate off and turned up a spline,put it back on and the torsion
bar is sticking out a few mil past spring plate end cap.I tried giving the torsion bar a few wacks with a hammer to no avail. Now this is my question.
Do the torsion bars meet in the middle and could the side i did first be over too much and stopping the other side from pushing in?
|
|
|
whathaveidone
Custom Title Time!
Posts: 1559
Threads: 98
Registered: February 24th, 2010
Member Is Offline
Location: Dapto
Theme: UltimaBB Pro Blue ( Default )
Mood: Heading for 10.99
|
| posted on March 20th, 2012 at 08:10 PM |
|
|
unload it and make sure the splines all line up,give it a few taps(not wacks ) should go in. had the same problem with mine not long ago but mine went
in to far. not sure how they can stick out as the spring plates have bits pressed over so they cant stick ouyt???
|
|
|
karmad
Casual Dubber
Posts: 30
Threads: 11
Registered: June 10th, 2011
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 21st, 2012 at 02:32 AM |
|
|
Is there an allen key or something holding the inner spline end in because even with a good few hard wacks of a hammer i cant get either side out
|
|
|
Aussie Dubbin
Fahrvergnugen
Posts: 895
Threads: 90
Registered: July 21st, 2008
Member Is Offline
Location: Adelaide
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 21st, 2012 at 07:17 PM |
|
|
Use some longer bolts or threaded rod to get the end cap on then swap back to stock One at a time
|
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
Posts: 8636
Threads: 559
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
| posted on March 21st, 2012 at 09:01 PM |
|
|
Hi
The spline hole goes all the way through so if one side goes in too far it could stop the other side from going in all the way. There is normaly a
build up of muck to stop this happening.
2 longer bolts fitted diagonally will let you pull it down enough to get the original bolts in.
Steve
|
|
|
68AutoBug
A.k.a.: Lee Noonan
Aircooled Master
Beetle Restorer - Experience over 138% - YIKES --
Posts: 11654
Threads: 449
Registered: August 31st, 2002
Member Is Offline
Location: SCONE in UPPER HUNTER VALLEY NSW
Theme: UltimaBB Pro Yellow
Mood: Really Mentally Ill - all of the time -
|
| posted on March 22nd, 2012 at 05:05 AM |
|
|
| Quote: | Originally
posted by karmad
Hi lads hope someone here can help me.I lowered the back of my 1303
by one outer spline on one side and proceeded to do the other side .I got the spring plate off and turned up a spline,put it back on and the torsion
bar is sticking out a few mil past spring plate end cap.I tried giving the torsion bar a few wacks with a hammer to no avail. Now this is my question.
Do the torsion bars meet in the middle and could the side i did first be over too much and stopping the other side from pushing in?
|
YES
LEE
- [size=4]Helping keep Air Cooled VWs on the road - location: SCONE in the Upper Hunter Valley - Northern NSW 320 kms NNW of SYDNEY--- [/size]
|
|
|
Arpspasm
Seriously Crusin Dubber
Posts: 112
Threads: 14
Registered: November 14th, 2009
Member Is Offline
Location: Maleny QLD
Theme: UltimaBB Pro Blue ( Default )
|
| posted on March 28th, 2012 at 12:18 AM |
|
|
| Quote: | Originally
posted by 1303Steve
Hi
The spline hole goes all the way through so if one side goes in too far it could stop the other side from going in all the way. There is normaly a
build up of muck to stop this happening.
2 longer bolts fitted diagonally will let you pull it down enough to get the original bolts in.
Steve
|
I had this problem as well though a long length of fish tank bubbler type hose on the end of the compresser gun blew it out very well. wear glasses
though the crud sprays out in quite a blast!!
|
|
|
