| [ Total Views: 563 | Total Replies: 6 | Thread Id: 97521 ] |
|
|
 beachbuggy61
Seriously Crusin Dubber
Posts: 162
Threads: 43
Registered: December 22nd, 2009
Member Is Offline
Location: Toukley, Central Coast NSW
Theme: UltimaBB Pro Orange
Mood: Hangin' to drive my bug!
|
| posted on June 21st, 2012 at 03:00 PM |
|
|
Case vacuum pumps
Hi all,
Does anyone have any experience with vacuum pumps for helping relieve windage pressure in the case?
I've seen talk about venting the rocker covers (although not 3-4 it would seem as that can get too oily!) and putting a vent where the fuel pump went
(can't do that cos it's where my turbo oil return goes), and the pumps I have seen are mechanically driven.
Anyone know of or seen electric pumps? Do they work? Are they worth it?
Tried searching thesamba too but there's a mountain of stuff when you type 'vacuum' into the search!
Thoughts, comments??
Thanks, Marc.
Baja
1915cc's of raw power 
Turbocharger
Intercooler
EFI
Crank fired Ignition
Runs E85
Engineered
"The Lord does not subtract from the life of a man, the hours spent on his Volkswagen" Anon. |
|
|
Stanley
Compulsive Aussie Vee Dubber
I guess the reward is in the doing of it
Posts: 4523
Threads: 270
Registered: March 13th, 2003
Member Is Offline
Location: Karalee...near Ipswich Qld
Theme: UltimaBB Psyche Grey
Mood: caught a bolt of lightning cursed the day I let it go
|
| posted on June 21st, 2012 at 03:28 PM |
|
|
whether it's electric or mechanical you'll still need a vent off your case.
|
|
|
beachbuggy61
Seriously Crusin Dubber
Posts: 162
Threads: 43
Registered: December 22nd, 2009
Member Is Offline
Location: Toukley, Central Coast NSW
Theme: UltimaBB Pro Orange
Mood: Hangin' to drive my bug!
|
| posted on June 21st, 2012 at 04:25 PM |
|
|
Hi Stanley, do you think the breather that comes off the oil filler would be enough or should I put another vent somewhere. I was thinking I could
hook up a pump to the breather tube that currently goes to my vent box...
Or maybe where the distributor used to go...
Thanks.
Baja
1915cc's of raw power
Turbocharger
Intercooler
EFI
Crank fired Ignition
Runs E85
Engineered
"The Lord does not subtract from the life of a man, the hours spent on his Volkswagen" Anon. |
|
|
vwo60
Veteran Volks Folk
Posts: 2036
Threads: 71
Registered: February 13th, 2007
Member Is Offline
Location: Pomona Qld
Theme: UltimaBB Psyche Blue
Mood: good
|
| posted on June 22nd, 2012 at 08:24 AM |
|
|
I have vents on both tappet covers and have replaced the filler with a breather box, its large enough to sort out any oil issues, it does not vent oil
at all, this is on a 2275 with a fk87 anf 10.8 CR. it still has the rear pulley scroll seal and does not leak there.
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on June 22nd, 2012 at 08:40 AM |
|
|
Fix the problem that's causing the high crankcase pressure, not the symptom.
Vac pumps are for ultimate race engines that are chasing every last ounce of horsepower.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
beachbuggy61
Seriously Crusin Dubber
Posts: 162
Threads: 43
Registered: December 22nd, 2009
Member Is Offline
Location: Toukley, Central Coast NSW
Theme: UltimaBB Pro Orange
Mood: Hangin' to drive my bug!
|
| posted on June 22nd, 2012 at 09:19 AM |
|
|
Thanks Matt. You're right, never good to just chase the symptom. I don't really have a major issue, was just looking to see if it was worthwhile.
I will, however, vent the rocker covers as well to make sure it's free to breathe!
Baja
1915cc's of raw power
Turbocharger
Intercooler
EFI
Crank fired Ignition
Runs E85
Engineered
"The Lord does not subtract from the life of a man, the hours spent on his Volkswagen" Anon. |
|
|
SuperOwen
Fahrvergnugen
Posts: 868
Threads: 67
Registered: January 18th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 23rd, 2012 at 12:37 PM |
|
|
Get the largest breather box you can. I like the CSP one with 4 1/2 inch fittings to go to the engine and 2 more for venting that are separated from
the others by an internal baffle to try and keep oil and air separated. You could go one step further and try run the 2 vents to the intake between
the air filter and turbo instead of just venting to atmosphere, but try not to suck oil through.
|
|
|
