[ Total Views: 1484 | Total Replies: 6 | Thread Id: 101417 ] |
|
aintgotitmusthaveit
A.k.a.: Nick
Officially Full-On Dubber
 
Posts: 295
Threads: 75
Registered: June 14th, 2006
Member Is Offline
Location: Melbourne
Theme: XMBX Pro Green
|
posted on March 31st, 2013 at 02:54 PM |
|
|
fuel Injection set up- photo added!
Never used brand new weber bolt pattern throttle body similar to injection perfection throttle body for fuel injection set ups. Throats are 50mm
diameter
Take a look at http://www.injectionperfection.com/
If you are setup now with a a single weber (NA) or boosted, unbolt your weber and bolt this throttle body on!
It comes with TWO chrome fuel rail and 4 red injectors (red injecters off an RX7 (these alone are worth more than the sell price of the lot!
Also included in a microtech MT4 fuel only ecu
Matching Loom all brand new
A hand held controller for the MT4 ECU
Ecu manual is included
Beauty of this is you dont need new manifolds- your existng dual port manifolds will suffice as your injecting into the throttle body.
Also comes with an aluminium plenum with built in ventury shaped intakes.
All items (except the injectors) are new.
I'm loosing interest in tinkering so its up for sale.
Its is by no means a complete kit, but for those wanting to go injected on a big HP motor (good for upto 400HP easy!)its a great start. you will still
need to source a Throttle position sensor, fuel injection clips and swirl pot fuel injection pump and some other bits but is a great start with
quality gear and minimal if any fabrication required. PS there is no base map- dyno time is likley to get you to run
$720 or nearest offer
Pick up from West melbourne or can post to you
PM me email address for photos, or call me Nick on 0410461072.
|
|
fish26
A.k.a.: benito
Fahrvergnugen
  
Posts: 903
Threads: 38
Registered: July 13th, 2007
Member Is Offline
Location: sydney
Theme: UltimaBB Pro Grey
Mood: Ken awesome
|
posted on March 31st, 2013 at 10:09 PM |
|
|
pm sent
bitten by the bug..........several times
|
|
1303Steve
A.k.a.: Steve Carter
Scirocco Rare
       
Posts: 8650
Threads: 564
Registered: August 27th, 2002
Member Is Offline
Location: Sydney, NSW
Theme: UltimaBB Pro Blue ( Default )
Mood: Parrot Heading
|
posted on April 1st, 2013 at 08:38 AM |
|
|
Hi
So is that a single dual throttle body?
Steve
|
|
aintgotitmusthaveit
A.k.a.: Nick
Officially Full-On Dubber
 
Posts: 295
Threads: 75
Registered: June 14th, 2006
Member Is Offline
Location: Melbourne
Theme: XMBX Pro Green
|
posted on April 1st, 2013 at 05:35 PM |
|
|
Yep
It's a single dual throat just like a weber dcoe, idf ida or dellorto equivalent
|
|
aintgotitmusthaveit
A.k.a.: Nick
Officially Full-On Dubber
 
Posts: 295
Threads: 75
Registered: June 14th, 2006
Member Is Offline
Location: Melbourne
Theme: XMBX Pro Green
|
posted on April 1st, 2013 at 07:10 PM |
|
|
Here is a photo of th bits
I also found a 4AGZE Throttle position sensor that I will throw in
There were some solenoids in the kit also that I forgot about
I suggest you check out injection perfections link and prices- you will see that this is an absolute bargain at 700 compared to replacement value!
http://i1274.photobucket.com/albums/y430/aintgotitmustahaveit/efi_zps0c7a0d18...
|
|
DubCty
Slammed & Awesome Dubber

Posts: 95
Threads: 11
Registered: June 11th, 2009
Member Is Offline
Location: Launceston, Tas
Theme: UltimaBB Pro Blue ( Default )
Mood: MAD™
|
posted on April 1st, 2013 at 09:22 PM |
|
|
I'll take it, If your happy to ship to Tassie thanks, Will call tommorrow
Cheers AL
Straight Cuts – The Best Preparation For A Wife!
|
|
aintgotitmusthaveit
A.k.a.: Nick
Officially Full-On Dubber
 
Posts: 295
Threads: 75
Registered: June 14th, 2006
Member Is Offline
Location: Melbourne
Theme: XMBX Pro Green
|
posted on April 2nd, 2013 at 11:58 AM |
|
|
Quote: | Originally
posted by DubCty
I'll take it, If your happy to ship to Tassie thanks, Will call tommorrow
Cheers AL
|
All yours Alistair
I've smsd you bank details
I'll cover the postage
Thanks
|
|