| [ Total Views: 6627 | Total Replies: 48 | Thread Id: 76880 ] |
| Pages: 1 2 |
|
|
 orange_spitfire
Learner Dubber
Posts: 13
Threads: 2
Registered: May 30th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 30th, 2009 at 10:15 AM |
|
|
Subaru transmission questions- need specifics
Hello from Florida!
I'm working on a way to use different transmissions in bugs busses and beetles; particularly Subarus due to their popularity and I need some
help. Can anyone tell me the overall length of the subaru transmissions and the length of the subaru axles per your most popular models for swap? I
think I have an acceptable method of using the stronger drivelines from the Subaru cars. Also, does anyone know the length and width of the VW
transmissions?? I do have one but I haven't removed it yet to measure and this info would be helpful if it is known.
Thanks in advance!
Rob
|
|
|
ttriebler
Officially Full-On Dubber
Posts: 321
Threads: 16
Registered: January 5th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 30th, 2009 at 06:34 PM |
|
|
Hey Rob, 2WD or 4WD? BBy far the most common Subaru transmissions downunder are the 4WD ones. I can get you the length of those if that's what
you're after. By the way, in their standard form their length means that you have to cut the torsion bars to fit them.
However a 2WD version is a different story, or a 4WD version with the centre diff removed to make it 2WD is also very short and would most likely not
need the torsion bars cut.
Let me know which you are after and I can take some measurements for you.
Reversed gears for Subaru transmissions.
Fit a Subaru 5 speed to your rear engined car
www.subarugears.com |
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 31st, 2009 at 01:46 AM |
|
|
Looking for that special lady : PM me for coffee & cake
|
|
|
ttriebler
Officially Full-On Dubber
Posts: 321
Threads: 16
Registered: January 5th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 31st, 2009 at 05:21 AM |
|
|
Yeah, may the force be with him
Reversed gears for Subaru transmissions.
Fit a Subaru 5 speed to your rear engined car
www.subarugears.com |
|
|
orange_spitfire
Learner Dubber
Posts: 13
Threads: 2
Registered: May 30th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 31st, 2009 at 09:03 AM |
|
|
Thanks ttreibler, I'm looking for the 2wd models for my own project but eventually I'm looking for all of them. If my plan is correct, you'll be
able tgo use any of them(what you do with the other end is up to you). I know it has been attempted to use the subaru trans before with disasterous
results but I think I have a new handle on this. .......by the way seagull, why the long face?? 
|
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 31st, 2009 at 07:37 PM |
|
|
The only way you can do it is to fit the motor behide your front seat . Mike it Perth has done it & I had a look today , he is running a WRX motor
as well. I take some photos next time I am down that way and post them up . The front is running A arms and coil overs , fully cadged out
Looking for that special lady : PM me for coffee & cake
|
|
|
orange_spitfire
Learner Dubber
Posts: 13
Threads: 2
Registered: May 30th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on May 31st, 2009 at 11:08 PM |
|
|
Cool, I'd like to see them seagull. I do understand what you are saying but I think I have a solution for the configuration. I don't want to get
anyone's hopes up until I can get the bugs worked out of my design but there IS a way to use this configuration in the typical VW fashion. I will
elaborate as things develop, I promise.
|
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 1st, 2009 at 12:42 AM |
|
|
1) your thinking of turning the crown wheel over
2) your thinking of flipping the gear box up side down
3) your thinking of getting a new crown wheel & pinon made
4) your thinking using the above and fitting a Front lsd center
5 = 
Looking for that special lady : PM me for coffee & cake
|
|
|
orange_spitfire
Learner Dubber
Posts: 13
Threads: 2
Registered: May 30th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 1st, 2009 at 01:21 AM |
|
|
NONE OF THE ABOVE!!!
|
|
|
orange_spitfire
Learner Dubber
Posts: 13
Threads: 2
Registered: May 30th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 1st, 2009 at 01:23 AM |
|
|
What I can tell you is that it HAS been done before in other applications and not for this purpose specifically but it should work nonetheless.
|
|
|
ricola
Wolfsburg Wizard
Posts: 437
Threads: 9
Registered: February 5th, 2003
Member Is Offline
Location: UK
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 1st, 2009 at 06:50 AM |
|
|
Reverse rotation cams? a la corvair?
|
|
|
ttriebler
Officially Full-On Dubber
Posts: 321
Threads: 16
Registered: January 5th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 1st, 2009 at 09:35 AM |
|
|
It's also possible to use planetary gears to reverse rotations. This could be done via an adapter plate between motor and gearbox or via the output
shafts to reverse their rotation. I also looked into putting planetary gears on the input shaft of the low/high range Subaru gearboxes as they have a
split input shaft. This can be achieved however those gearboxes have teenny weeny input shafts and wouldn't be up to the task of handling any
power.
Good luck to you as many have gone before and failed.
Let me know when you wish to purchase your first set of reverse-cut crownwheel and pinion/output shafts from me.
I'll give you a great price shipped to your door in Florida.
Reversed gears for Subaru transmissions.
Fit a Subaru 5 speed to your rear engined car
www.subarugears.com |
|
|
orange_spitfire
Learner Dubber
Posts: 13
Threads: 2
Registered: May 30th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 1st, 2009 at 10:07 AM |
|
|
Suffice it to say that what I have in mind has been proven to handle quite a bit of torque in other apps so I think it will work. I just want to test
it first, then, once I know it will work, I'll fill you all in on it. I promise. As far as the measures of the transmissions go, are the Subaru
transmissions longer, wider or both than a type 1 trans?
|
|
|
ttriebler
Officially Full-On Dubber
Posts: 321
Threads: 16
Registered: January 5th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 1st, 2009 at 12:29 PM |
|
|
The 2WD ones are very very similar in dimensions to a type 1 trans. They fit inbetween the frame horns so aren't any wider.
Reversed gears for Subaru transmissions.
Fit a Subaru 5 speed to your rear engined car
www.subarugears.com |
|
|
waltermitty
Custom Title Time!
Legend when my beer goggles are on
Posts: 1993
Threads: 268
Registered: August 29th, 2002
Member Is Offline
Location: Port Macquarie now Yipee!
Theme: UltimaBB Pro Grey
Mood: Hungry for mor
|
| posted on June 1st, 2009 at 02:13 PM |
|
|
what about using reduction boxes as per a splitty? dont these reverse the rotation of the transaxle? M
23 windows ...8 too many!
|
|
|
ttriebler
Officially Full-On Dubber
Posts: 321
Threads: 16
Registered: January 5th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 1st, 2009 at 04:24 PM |
|
|
Yes they do but they 'jack up' the suspension on application of throttle. Not a great handling characteristic.
Reversed gears for Subaru transmissions.
Fit a Subaru 5 speed to your rear engined car
www.subarugears.com |
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 2nd, 2009 at 01:23 AM |
|
|
| Quote: | Originally
posted by ttriebler
It's also possible to use planetary gears to reverse rotations. This could be done via an adapter plate between motor and gearbox or via the output
shafts to reverse their rotation. I also looked into putting planetary gears on the input shaft of the low/high range Subaru gearboxes as they have a
split input shaft. This can be achieved however those gearboxes have teenny weeny input shafts and wouldn't be up to the task of handling any
power.
Good luck to you as many have gone before and failed.
Let me know when you wish to purchase your first set of reverse-cut crownwheel and pinion/output shafts from me.
I'll give you a great price shipped to your door in Florida.
|
Ok ,
If you have made the gear set I would love to have a chat about what you have done. The gear set I have seen was so crap it went 18 feet and snaped
the pinion like a twig.
Looking for that special lady : PM me for coffee & cake
|
|
|
ElusiveStranger
Officially Full-On Dubber
Posts: 330
Threads: 30
Registered: May 28th, 2006
Member Is Offline
Location: Kent. England
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 2nd, 2009 at 07:24 AM |
|
|
Well this guy did it
http://www.vwkd.co.uk/bb/viewtopic.php?t=1962
Edit Just realised it's not back to front, sorry
|
|
|
GeorgeL
Officially Full-On Dubber
Posts: 231
Threads: 11
Registered: February 5th, 2006
Member Is Offline
Location: 7200 miles off the Queensland coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 2nd, 2009 at 07:56 AM |
|
|
| Quote: | Originally
posted by ttriebler
Yes they do but they 'jack up' the suspension on application of throttle. Not a great handling characteristic.
|
There are ways to "full float" the RGBs so that you don't get that effect. Think of an old style BMW motorcycle versus the newer paralever
setup.
I've seen pictures of a Brasilian RGB IRS setup that has possibilities. The parts are probably unobtainium, though.
|
|
|
 matberry
Super Moderator
Go hard or go home
Posts: 8114
Threads: 134
Registered: March 7th, 2006
Member Is Offline
Location: Cooroy Qld
Theme: UltimaBB Pro Blue
Mood: enjoying waving at all my Kombi buddies from my T3
|
| posted on June 2nd, 2009 at 08:50 AM |
|
|
What about inboard reductions, they wouldn't effect the handling, could set up high/low or foward/aft even depending on application.
Matt Berry Motorsports...air cooled advice, repairs and mods Ph 0408 704 662
OFF-ROAD,CIRCUIT,DRAG,STREET,ENDURANCE
 |
|
|
orange_spitfire
Learner Dubber
Posts: 13
Threads: 2
Registered: May 30th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 2nd, 2009 at 12:16 PM |
|
|
Hey guys,
I was doing some brainstorming with a buddy of mine this evening and we're putting some sketches together right now. Thanks ttreibler for the
info on the width of the trans; I think it will become useful shortly. I've got a friend with an older (early 90's) Legacy non-turbo that he'll
donate for free- running and all so I have the most important part for the experiment. It is an automatic car so at least it will make shift linkage
easy. I'll get back with you all soon and let you all in on this as soon as I make sense of it all.
|
|
|
ttriebler
Officially Full-On Dubber
Posts: 321
Threads: 16
Registered: January 5th, 2008
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 2nd, 2009 at 06:50 PM |
|
|
Hey the idea of inboard reduction hubs is pretty awesome. You could have them so they are 'behind' the trans output. This would likely minimise the
'jacking up' effect and also alow the trans/motor to be further forward. The other alternative would be a planetary gearbox on the output. Rugged
and compact.
Reversed gears for Subaru transmissions.
Fit a Subaru 5 speed to your rear engined car
www.subarugears.com |
|
|
orange_spitfire
Learner Dubber
Posts: 13
Threads: 2
Registered: May 30th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 17th, 2009 at 07:15 AM |
|
|
Hey guys, time for an update... I've got my boxes roughly designed and now I'm looking for alittle input on straight cut gears and their strengths
and weaknesses. If anyone has any input or can recommend a differing type of gear, please let me know. My boxes are roughed out so I can alter
dimensions to suit my gear sizes so I am not limited to one particular size or ratio. Thanks for the input and all your help in advance. As
promised, I'll keep everyone updated as I go.
Rob
|
|
|
pete wood
A.k.a.: figure itout
23 Windows of Awesome
Posts: 6828
Threads: 389
Registered: January 15th, 2004
Member Is Offline
Location: Nth Nth StMarys, Sydney
Theme: UltimaBB Pro White
Mood: upgrades = jackstands
|
| posted on June 17th, 2009 at 06:25 PM |
|
|
helical cut is actually stronger and better for most applications.
|
|
|
bevoracing
A.k.a.: Tony Beven
Officially Full-On Dubber
Posts: 324
Threads: 35
Registered: January 18th, 2009
Member Is Offline
Location: Mount Pleasant SA
Theme: UltimaBB Vintage
Mood: Leaning against the shed wall !.
|
| posted on June 17th, 2009 at 09:44 PM |
|
|
Hi Orange
The strength of a helical cut is much higher than a straight cut OF THE SAME TOOTH PROFILE, but straight cuts usually have much larger teeth and can
be cut more easily from higher strength materials. One problem is that straight cut gears, and larger teeth, make a lot of noise and that's why car
manufacturers don't use them. They love gutless little engines with quiet little fine cut gears running to the limit of the strength of their cheap
materials.
BUT, to the main reason racing boxes have straight cut gears. Helical gears try to slide sideways across each other (think about it) and therefore
create side load on the bearings and thrust washers. This creates heat and the box fails by either overheating, which weakens and breaks gears, or the
thrust washers fail and the box falls apart. Put in straight cuts and all the load is taken straight against the bearings as they were designed to
take it. The “noise” (vibration) is hard on the bearings with heavy loads but you change them out regularly and the box lives, cool, strong &
noisy.
For what you want build it first with straight cuts and see how it goes, they’re cheaper to machine and will give less trouble, and bore noise. I’m
sure your gear man will advise you on what’s best for your design. Good luck. I look forward to seeing the results.
Cheers
Tony
|
|
|
orange_spitfire
Learner Dubber
Posts: 13
Threads: 2
Registered: May 30th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 18th, 2009 at 06:14 AM |
|
|
Thanks guys for the interest and info. I was thinking along those lines for the strenght part but I was more worried about my box design. In an
effort to keep them affordable and "bulletproof", I was planning on the straight cut gears pretty much. I'm wondering how thick they will need to
be to handle the HP of the nastiest application. If I can prepare the boxes for the worst application, I think they'll be great for us all.
Besides; whose worried about alittle gear noise anyway?? With most of these Suby cars out there, you'd be hard pressed to hear the gears over the
exhaust anyhow! Well, bear with me and I'll get an update with some fresh news about construction as soon as I can and thanks again to you all for
all your help!
Rob
P.S. does anyone know what the highest HP of these Subaru conversions is out there?? I don't have any idea so let me know. THANKS!!
|
|
|
GeorgeL
Officially Full-On Dubber
Posts: 231
Threads: 11
Registered: February 5th, 2006
Member Is Offline
Location: 7200 miles off the Queensland coast
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 18th, 2009 at 07:29 AM |
|
|
| Quote: |
P.S. does anyone know what the highest HP of these Subaru conversions is out there?? I don't have any idea so let me know. THANKS!!
|
With reasonably stock engines the turbo models go a bit over 300. With mods some say they can triple that. How fast do you want to spend? 
|
|
|
seagull
Compulsive Aussie Vee Dubber
Posts: 4979
Threads: 752
Registered: December 25th, 2003
Member Is Offline
Location: PerthWA
Theme: UltimaBB Pro Blue ( Default )
|
| posted on June 18th, 2009 at 08:11 PM |
|
|
Yawn !
nothing here
Looking for that special lady : PM me for coffee & cake
|
|
|
orange_spitfire
Learner Dubber
Posts: 13
Threads: 2
Registered: May 30th, 2009
Member Is Offline
Theme: UltimaBB Pro Blue ( Default )
|
| posted on July 3rd, 2009 at 12:57 AM |
|
|
Sorry to bore you seagull but I'm not equipped with a full service machine shop... And, do you want it fast or correct!? As before, bear with me
folks, I'm doing this on a serious shoestring budget.
|
|
|
Baja Wes
Bishop of Volkswagenism
V6 Baja Pioneer
Posts: 3119
Threads: 94
Registered: August 26th, 2002
Member Is Offline
Location: Brisbane
Theme: UltimaBB Pro Blue ( Default )
Mood: Content
|
| posted on July 4th, 2009 at 11:03 AM |
|
|
The problem with using reduction boxes is you lower the efficiency of the driveline, meaning less power at the wheels. Straight cut gears are more
efficient than helical gears, but you will still have some losses. For this reason I don't see the reduction box solution very suitable for street
cars that are chasing performance. So if you are only using it to reverse the rotation, but not lower the gearing, then I see it as being full of
disadvantages.
For an offroader you can have the benefit of lowering the gearing, so you might accept the loss of efficiency.
That's just my thoughts 
|
|
|
| Pages: 1 2 |
