Skip to content
Aussieveedubbers

Oil Pressure

0 likes
Share Share on Facebook Share on X Share on Reddit
Log in to reply

landfall Officially Full-On Dubber

290 posts · joined Jun 2014 ·

#1004070
Since fitting my oil pressure gauge and getting the car idling at the correct RPM 850/900 I am aware of a IMO poor oil pressure.

1600 DP engine.

When the oil warms to operating temperature and cruising at 2500RPM I have a pressure of 25/30psi, at idle 5psi.(light comes on) increase RPM to 1100 and light goes out at 7psi.

End float on crank is .008

Oil grade 20/50 Nulon.

Any diagnosis welcome.

Ken

fish26 Fahrvergnugen

903 posts · joined Jul 2007 ·

#1004098
already running 20W50, maybe try Penrite hpr30, there are a lot of oil pressure associated contributors namely bearing wear, oil pump clearance, sticky oil relief, beat out case, etc, etc.
bitten by the bug..........several times

landfall Officially Full-On Dubber

290 posts · joined Jun 2014 ·

#1004102
Will give the Penrite a go, don't really want to change to HPR 80😂

Craig Torrens 6 times Australian, 7 times State Hillclimb Class Champion

8,040 posts · joined Jan 2003 ·

#1004112
Put a 30mm oil pump on it.


psimitar Son of Jim - Creator of Good

2,506 posts · joined Jan 2009 ·

#1004115
Get a garage to screw a mechanical oil pressure gauge into where the sender unit goes. This will then give you a true idea of the engines oil pressure as the electric types can be rather hit or miss when it comes to accuracy as even a change in supply voltage to the gauge can affect the gauges reading.

Once you have a good baseline to work from then try some 60 weight oil that they sell now for old worn engines.

Then check out the oil relief valves for fit and scoring.

Then if still low remove the pump and check the pump cover for wear and backlash of the gears.

If none of this raises any obvious culprits then means the crank bearings need looking at.
madness is in the eye of the beholder 👍

modnrod Fahrvergnugen

978 posts · joined Mar 2011 ·

#1004118
Raise the idle up, then just drive the thing.
If it wasn't for that silly little tell-tale you wouldn't have even known about it. At some point, and my guess it not very soon, a loud clunk and rattle will announce you now have the chance to throw in something new and shiny.
Woo!hoo! 😀

PS: Maybe ease up on the big-rev side-steps at the lights a bit though.........

landfall Officially Full-On Dubber

290 posts · joined Jun 2014 ·

#1004126
modnrod wrote:Raise the idle up, then just drive the thing.
If it wasn't for that silly little tell-tale you wouldn't have even known about it. At some point, and my guess it not very soon, a loud clunk and rattle will announce you now have the chance to throw in something new and shiny.
Woo!hoo! 😀

PS: Maybe ease up on the big-rev side-steps at the lights a bit though.........
That's the theory I am currently working on.

Currently have all the ingredients to build a nice shiny new engine, ust need a new case.

Would like to keep it mobile until next winter.

Ken

Paul Smith Casual Dubber

43 posts · joined Jul 2012 ·

#1004129
If you are worried about slightley low oil pressure doing damage add Nulon E 10. The Teflon bakes onto internal parts and will keep everything protected. I used to have a 65 Chevy that burned so much oil that it would have the red light on the dash glowing until pay day when I would add more oil and it just kept going to to Nulon. I also had an old Datsun ute that had a very stubborn 2nd gear synchro. I added Nulon gearbox treatment and the problem went away.

landfall Officially Full-On Dubber

290 posts · joined Jun 2014 ·

#1004132
Paul, I am a big Nulon fan.

In fact I wrote a recommendation for them and they published it and gave me a $200 voucher to spend at the local Nulon dealer.

Ken